Question about 2000 Toyota Tundra

1 Answer

Rear end went out on 2000 tundra need instructions how to install it

Got new rear end need help directions to remove and replace

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

Block the front tires, jack up the rear end. Remove driveshaft from rear end. Loosen but do not remove the leaf springs and the shock absorbers. Remove the brake lines and the emergency brake cable. Return vehicle to ground and finish removing the leaf springs and the shock absorbers. The vehicle will have to be slightly raised to do this. The other option is to replace the ring and pinion as a unit which requires a completely different set of instructions. What will you be doing, replacing the entire axle and housing or just the ring and pinion?

Posted on Apr 18, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
KAComstock
  • 274 Answers

SOURCE: I need to replace starter

No you do not need to remove the plenums. The starter is removed and installed from underneath the truck of from within the wheel well if the wheel is removed. You should go buy a Haynes or Chilton repair manual for $20 they are indisposable to do it yourselfers and will give detailed step-by-step instructions with pictures.

Posted on May 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing a starter


1 disconnect battery 2 remove any wires connected to the starter 3 remove mounting bolts 4 catch the starter and manouver it through your suspincion 5 you may need to reverse 2 and 3 depending on how hard the wires are to get to 6 now revers these steps with new starter

Jul 24, 2014 | 2000 Toyota Tundra

2 Answers

I have a 2000 Toyota Tundra - front end shimmys at speeds over 55 mph or braking at high speeds - could it be front tires need to be rebalanced, or front end realigned?


new tyres needed would be more the cause as they do deform with the sun in hotter climes ,and no doubt they are twisted if you look carefully

Aug 24, 2011 | 2000 Toyota Tundra

1 Answer

I need help on how to change a headlight bulb on my 2000 toyota tundra


  • 1 Open the Tundra's hood and locate the back of the headlight assembly inside the engine compartment.
  • 2 Unplug the electrical connector from the assembly and remove the rubber cover from the bulb socket.
  • 3 Release the retaining spring to loosen the old bulb, and then pull it directly out of the socket. Carefully dispose of the bulb to prevent it from cracking or shattering.
  • 4 Align the tabs of the new bulb with the cutouts of the mounting hole. Then, carefully press the bulb into the socket until it's secure.
  • 5 Install the rubber cover in its original position and reattach the electrical connector to the headlight assembly. Make sure the rubber cover is fastened to the socket before continuing.
  • 6 Start your Tundra's engine and test the headlights to make sure they work before closing the hood.

Jul 30, 2011 | 2002 Toyota Tundra

1 Answer

I need to replace starter motor in my 2000 Toyota Tundra 4.7 L V8. Do I need to remove the upper and lower plenum?


No you do not need to remove the plenums. The starter is removed and installed from underneath the truck of from within the wheel well if the wheel is removed. You should go buy a Haynes or Chilton repair manual for $20 they are indisposable to do it yourselfers and will give detailed step-by-step instructions with pictures.

May 12, 2011 | 2000 Toyota Tundra

1 Answer

How do you change a 07 toyota tundra serentine belt


Insert a ratchet or breaker-bar drive (end of bar) into the square hole in the tensioner / idler pulley mount. Move the tensioner mount in whatever direction is required to release tension on the belt. You will then be able to remove the belt. Install new belt similarly -- there should be a routing diagram under the hood for the belt -- if not, it would be a good idea to diagram it yourself before you remove the old one.

Charlie

Jan 09, 2011 | 2007 Toyota Tundra

1 Answer

How do i change 2004 toyota tundra rear end drive shaft


1st, with th E brake on and the wheels chocked. Remove the 4 bolts that connect the shaft to the
rear end flange and pull(or pry if required)away from the rear end. Next pull the shaft back toward the rear off of the front spline. You may have to remove the seal from the from the front of the shaft
at the spline to pull the shaft all the way off. Somtimes the grease on the spline creates a vacum
that makes it tough to remove. When you install the shaft there are marks or notch's on the shaft
and rear end flanges to line up as well as the spline+yoke. But an old rule of thumb is make sure
that the U joints are all in line, so if one shaft is at 12:00 ( I ) the other must be at 12:00 also.
Once the shafts are lined up, line up the marks on the flanges and bolt it up.
Hope this helps.

Dec 01, 2010 | 2004 Toyota Tundra

1 Answer

How to replace alternator on 2007 toyota tundra


Hi. Please see procedure below:

Determine which alternator your Toyota Tundra will need. You'll want to be sure the new alternator is compatible with your Tundra's engine. Models built from 2000 to 2004 have a 3.4 L or 4.7 L engine. Models made from 2005 to 2006 offer options for a 4.0 L or 4.7 L engine. Starting in 2007, the Tundra is available with 4.0 L, 4.7 L and 5.7 L engines.

Disconnect the negative battery cable with a socket wrench. Remove the gravel shield if you need to access the alternator from under the car. Remove the electrical connector and unfasten the retaining nut on the alternator terminal with a socket wrench. This will allow you to remove the battery terminal wire.

Unfasten the lock nut, pivot bolt and adjusting bolt on the alternator with a socket wrench. Remove the drive belt and take the alternator off the vehicle.

Install the new alternator assembly. Use a torque wrench to tighten the lock nut to 25 ft. lbs. and the pivot bolt to 38 ft. lbs. Attach the adjusting bolt.

Connect the electrical harness and battery terminal wire to the alternator and fasten the retaining nut to the alternator terminal with a socket wrench. Install the gravel shield if you removed it. Replace the drive belt and restore it to the proper tension. Reconnect the negative battery cable with a socket wrench.

Thanks!

May 25, 2010 | 2007 Toyota Tundra

1 Answer

Changed timing belt and need to know how to set the timing


For your 2000 Toyota Tundra: I do not know if you have the 3.4L DOHC V6 or the 4.7L DOHC V8.

Click on the following free, direct Link. It has all the Timing Belt Diagrams you will need, complete with Instructional and Directional Diagrams to set your Timing.

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2000/make/toyota/model/tundra/2000_toyota_tundra_timing_belt_diagram_marks.htm

Apr 04, 2010 | 2000 Toyota Tundra

3 Answers

2000 tundra v8


i would buy a factory or nippondenso sensor. not some aftermarket junk

Oct 01, 2017 | 2000 Toyota Tundra

1 Answer

Getting a vibration when i accelerate


You will need to check the drive line the yokes and also the rear end. A lot of times what happens is the drive line is bent or not balanced and needs to be balanced at a drive line shop.

Feb 21, 2009 | 2000 Toyota Tundra

Not finding what you are looking for?
2000 Toyota Tundra Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...