Question about 2001 Dodge Stratus

1 Answer

How to remove plastic clips - 2001 Dodge Stratus

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 176 Answers

Turn the Wheel on the right side to gain acces use a small soket and ratchet to unscew 6 scews to remove the cover in the Wheel house you dont have choice sometime it is had because screws rust into plastic clip may be you will need biger screws after,to disconnect the battery slide the battey out a bit to reach cable

Posted on Apr 18, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove door panel ( driver's side )?


remove plastic plugs in armrest, screws behind to undo. remove plastic plug from interior handle eschutchion and small screw.the panel is held on by plastic clips which usually break when you remove panel .to remove panel prize away from door using a trim remover or a screwdriver with care! the clips are a very tight fit.the panel hooks over the window seal at the top. hope this helps.

Oct 08, 2015 | 2001 Jaguar XJ8

Tip

Replace Turn Signal Bulb


If you look straight up inside the bumper you will see the plug that holds the bulb just twist and it will come out.

  1. Open the hood and remove the plastic clips that hold the front plastic splash guard in place. This is done by pushing on the center of the plastic buttons to depress them slightly. The button (clip) can then be removed. For the buttons (clips) with the philips head center, lift the philips head center until you hear a click and then remove the whole clip.
  2. Remove the plastic splash guard.
  3. Remove the three 10mm bolts that hold the lens assembly to the fender.
  4. On the fender side of the lamp assembly there is a plastic clip that is inserted in a small flange which is part of the fender. Use a flat screwdriver to put pressure on the back of the post that protrudes through this clip. This post, that is part of the lamp assembly, helps to hold the assemble in the correct position. Once that post is free of the clip the lens assembly can easily be removed.
  5. Un-clip the wires to the main headlights and the the parking/turn signal lamp and remove the lens assembly from the vehicle.
  6. In the case of a fast blinking turn signal, remove the turn signal bulb, test to be sure it is good, and clean the contacts of the blub, bulb holder, and the printed circuit strip on the lamp assembly.
  7. Reassemble everything and test.
  8. Replace the lamp assemble in the fender and secure the splash guard with the clips.
  9. This should be about a 1/2 hour job.

on Mar 17, 2010 | Lexus ES 300 Cars & Trucks

1 Answer

Need to change right tail light, how?


Open hatch, on inside there will be two plastic clips that go into the side of the tail light, remove the center of the plastic clips, they will pop out, remove the rest of the remaining clip, once you have the plastic clips out, tail light will come off, no screw's holding tail light, just those two plastic clips.

Sep 01, 2010 | 2006 Chrysler Town & Country

1 Answer

I would like to replace the head lights of my volkswagen chico 1.3L 2001 model, but I don't know how to remove the plastic grill in front of it.


The grill has plastic clips on the top side. The clips have a plastic center pin that must be pushed through. once the pins are out you can lever the clips up, using a small flat screw driver. the grill can then be pulled fowards and upwards to remove.

Jun 02, 2010 | 1985 Volkswagen Golf

1 Answer

How do You remove the plastic clips to pull the air intake tube


thats the part load breather pipe. you should be able to remove it by squeezing the plastic clip together by hand but it may have hardened by age making it difficult and can break be carefull not to break the stub on the cam /valve cover if in doubt cut the pipe off carefully and fit a new one. by gentle twisting/squeezing they nomally come off

Apr 03, 2017 | 2000 Jaguar XK

1 Answer

How to remove a door panel on a 1995 pontiac grand


I have info on a 96 power door glass.....should be very simular. the triangle piece at the top front is just clipped on, the plastic piece around the opener handle is just clipped on. in the pull handle there are two screws, and the plastic piece just pops up. under the red reflector the is a screw. There is a "U" clip behind your window crank, remove this clip and the crank will pull straight out. (use a screw driver to open the gap between the crank and the door panel, to see the clip, Use a hook tool too remove the clip...you can also use a cloth or panty-hose in the gap and turn the crank, the cloth will grab the edge of the clip and pop it off)
after removing all the clips and screws the door panel is held on with plastic plugs, just pull the panel sraight out toward youself.
hope this helps.


14e9333.jpg
4604e0c.jpg

Apr 01, 2010 | 1995 Pontiac Grand Am

1 Answer

Remove door panel driver door


by the door handle remove plastic trim atatched with veltcro start removing plastic clips with a clip remover some might break as some are meant to break when taken off

Dec 31, 2009 | 2000 Cadillac DeVille

1 Answer

Removal of rear outter door handle


Ok
Remove plastic plug on the inside of door there is 10 mm hole use a hooked pick set pick put through the hole and pull the plastic cir clip towards the back of the door that will release the smaller part of the outer handle then the handle itself can be taken out.this is so simple but so deceiving the actual cir clip is hard to notice because of all the plastic **** on the inside backing plate the cir clip is just on the inside of hole look hard it is 2mm thick & 20mm high (black plastic) place point of pick in between backing plate & cir clip hook it and pull back the front door is based on the same principle but is a lot easier

Jun 10, 2009 | 2008 Audi Q7

2 Answers

Removal of interior door pannel on left rear door


Normal 0 Quite simple. Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

May 30, 2009 | 2001 Cadillac Seville

2 Answers

How to remove the tail lights from a 2003 murano


Here's the step by step procedure from the beginning.
  1. Carefully remove the black one inch wide plastic molding strip that runs along the interior side of the tail light. This can be pried off carefully without breaking the plastic clips that hold it in place.
  2. Using a 10mm socket, remove the two bolts that you see which secure the tail light housing.
  3. The tail light housing is also held in place with three or four plastic clips which can be broken rather easily if you don't do this next step carefully. Begin prying the plastic tail light using a plastic putty knife or screwdriver. The top clip comes out pretty easily and so does the bottom one.
  4. On a cold winter day, the middle clip is the one that can break rather easily so gently rock the tail light or wait for warm weather when the plastic isn't brittle.
  5. Once the tail light "bucket" is removed it's a simple matter to replace the bulbs.
d87baef.jpg

Oct 03, 2008 | 2003 Nissan Murano

Not finding what you are looking for?
2001 Dodge Stratus Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...