Question about 1999 Chevrolet Silverado 1500

1 Answer

Key fob dont work, but door lock works ok, key fob battery change.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1. Get in your vehicle.
2. Close the door.
3. Put key in ignition
4. Do not turn on the ignition yet.
5. Hold down on the unlock button on the door panel. Do not let up.
6. Turn the key to ON, OFF, ON, OFF (while still holding the unlock button on the door panel).
7. Release the unlock button.
8. The door locks should cycle, indicating that you did everything correctly.
9. Have all your remote entry fobs available. Hold down on both the lock and unlock buttons until the door locks cycle. Do the same on all key fobs. This will re-program all of them.
10. Turn ON the ignition key to exit the program mode.
11. DONE.

Posted on Apr 18, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 32 Answers

SOURCE: Key fob stopped working the door locks. I changed

the circuit boards on those factory remotes, sometime break where the battery is clipped in, check to make sure the solder is holding the clip properly and it is not loose, also they remote may need to be programmed to the vehcile with a scan tool, usually only found at GM, Also the rubber part of the remote on the inside where the pad touchs the circuit board, uses a small screwdriver and touch the exposed circuit, if the remote locks the doors, try putting in tiny peice of alumumn tape of the inside pad, the connectiveness of the rubber wears off. If not try above or dealer.

Posted on Oct 02, 2009

ZJLimited
  • 17970 Answers

SOURCE: 2005 cobalt ls, 24000 mi,

Most commonly if this is a bad receiver, when receiver start going bad they will work and not worked intermittently. The most you can do at this point is try to reprogram the system and see if it begins to work properly again otherwise it's gonna be time to replace the receiver. Part of the receiver is working, see the receiver receives your signal but then it must perform an action and it's the action part of the receiver that has the problem.

If the reprogramming must be done at the dealer with a factory scanner, unfortunately the other scanners available will not do this.

Keep in mind that the best place to possibly get a replacement key fob would be from the dealership. They will be able to sell you the fob and program it to your vehicle for you as well. Also if you need any extra keys you can get them there as well.

Hope this helps. Keep us updated.

Posted on May 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key remote won't lock the door change fuse and battery in remote still don't work


Common Reasons Why Your Car Door Isn't Locking Properly The key fob battery is dead: This is one of the most common reasons why your car door lock is not working. If your locks aren't working, replacing the battery in the key fob could solve the issue. The key fob is faulty: If the battery isn't the problem, the issue may be with the fob itself. If you go to your car dealer, they can hook the fob up to a computer and make sure that the programming is still good. If it's not sending a signal, the fob will likely have to be replaced. A fuse is blown: If one door doesn't work, but others do, the problem could be a blown fuse. Replacing the fuse will correct the problem. This is a cheap and easy fix The solenoid is bad: Again, if one door doesn't work, but others do, the problem could be with the door lock solenoid. Replacing it may require removing the car door panel You have a broken wire: If the lock isn't getting power, hold the lock switch either up or down, and then open and close the door repeatedly to see if the lock will work. If it works sometimes, you probably have a broken wire

Sep 28, 2016 | Cars & Trucks

1 Answer

Key fob wont work any more (battery was change


Go to this link and follow the instructions posted:

http://www.ehow.com/how_7187975_reprogram-dodge-key-fob.html

Apr 18, 2014 | 2009 Dodge Dakota Crew

1 Answer

Key fob


Sometimes when you change batteries you have to re-sync the remotes to the vehicle. Check your owners manual, you may be able to lock and unlock the driver's door with the key to do it.

Aug 03, 2012 | 2004 Buick Rainier

1 Answer

Key locked in 2001 pontiac grand prix battery is


lock smith or someone authorized to use a slimjim[can do more damage if dont know how to use ]--or-- key fob wont work if vehicle battery dead if u can reach up under car at front and release hood latch then jump battery and then use key fob to unlock door

Feb 20, 2010 | 2001 Pontiac Grand Prix

3 Answers

My Porsche Key fob no longer unlocks the doors


Insert key into door barrel or ignition lock and turn key, whilst doing this press the unlock/lock button, the led on the dash should flash to indicate this has initialised the key to the car, then remove key and test operation of remote. If this fails then a new remote plus coding to the car by your dealership is needed

Feb 16, 2010 | 2005 Porsche 911

2 Answers

Key fob lights up but doesn't work even with a new battery


I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!

Aug 25, 2009 | 2000 Renault 181

1 Answer

HELP HELP !!!!!!! Electric fault i think !!!!!!!!!!


1....ensure the battery in the "Key Fob" is OK............Press either Lock or Unlock button for more than 1 second, the lamp on the fob will light if OK. Change battery if it does not illuminate! 2.....if battery on fob OK.......Re Syncronise the key fob to the car by:.... a brief press on either button twice and within 30 seconds turn Key to position 2 on the ignition lock
Hope that fixes it...let me know?

Nov 09, 2008 | 1998 Mercedes-Benz C-Class

1 Answer

Mark 4 golf, heated seats and central locking


basic but have you checked the fuse.

Sep 17, 2008 | 2001 Volkswagen Golf

1 Answer

I have a grand voyager limited diesel. The central locking has stopped working, both via the key fobs and inside the car.However, the key fob still opens the side doors as well as the boot. Same problem...


dont go through all the hassles of removing the door trim just take the terminal off the battery for about a minute then reconect again worked on mine good luck

Jul 30, 2008 | 2004 Chrysler Voyager

3 Answers

Mercedes S320 central lock


if you hav a remote control key &yr car wont respond . change key batrrey &contact dealer if still dont work for software

Jul 13, 2008 | 1994 Mercedes-Benz S-Class

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...