Question about 2007 Hyundai Santa Fe Limited

Open Question

Driver door will not lock with remote or button

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5370 Answers

SOURCE: Right front door dosen't always lock on 2002

You most likley have a faulty door lock actuator. Unplug the actuator and connect a test light to the connector, then push the switch to see if the test light illuminates. ------------It Sounds like the locking actuator is either sticking or has gone faulty. The door panel needs to be taken off to access the actuator and the mechanism has to be checked.------

Well if you want to fix this problem then you will need to get inside your drivers door panel. Once you have the panel off then you will see a rod. A rod connects the actuator to the latch, and another rod connects the latch to the knob that sticks up out of the top of the door. Then you will se a actuator. When the actuator moves the latch up, it connects the outside door handle to the opening mechanism. When the latch is down, the outside door handle is disconnected from the mechanism so that it cannot be opened. This system is quite simple. A small electric motor turns a series of spur gears that serve as a gear reduction. The last gear drives a rack-and-pinion gear set that is connected to the actuator rod. The rack converts the rotational motion of the motor into the linear motion needed to move the lock. When the motor spins the gear, the clutch swings out and locks the small metal gear to the larger plastic gear, allowing the motor to drive the door latch. If you move the door latch yourself, all of the gears will turn except for the plastic gear with the clutch on it. You will need to play with the powered door lock buttons a little to see what's loose and why its not working well with that door. If the gears are not moving or stuck inside the actuator needs to be replaced.

--------

Click this link below for more details:---

http://howtobyme.blogspot.com/2011/08/how-to-remove-door-lock-actuator-on_29.html

-------

This will help.Thanks.Helpmech.

Posted on Aug 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My remote unlocks my doors but the lock door button stopped working last night


Return your Pilot to where you had the recall work done and give them the opportunity to complete the job to your satisfaction.

Jul 21, 2017 | 2004 Honda Pilot

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

1 Answer

Central locking fob


Programming
When
Remote control buttons operated repeatedly while vehicle out of range and system becomes inoperative. System malfunction.
How
Ensure ignition switched OFF and all doors closed. Proceed as follows: Within 10 seconds, open driver's door and switch ignition ON. Within 10 seconds of switching ignition ON, switch ignition OFF. Within 20 seconds of switching ignition OFF, press and release driver's door contact switch 3 times. Within 10 seconds of releasing driver's door contact switch, switch ignition ON then OFF. Within 20 seconds of switching ignition OFF, press and hold both remote control buttons in turn for at least 5 seconds. The driver's door should lock and unlock once. Within 5 seconds of driver's door locking/unlocking, press remote control lock button Fig. 1 [1] or unlock button [2]. Programming procedure complete. Confirm programming has been successful by locking and unlocking vehicle.
NOTE: A maximum of 2 remote controls can be programmed.

Feb 05, 2010 | 2002 Suzuki Grand Vitara

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Un work of the doors auto control lexus


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

2 Answers

Drivers Door Lock Problem


Press the passenger side door lock button. if the driver side door unlocks now but wont unlock when you hit the driver side door lock button, it is usually a network communication problem with the B CAN or a faulty Body Control Module.

May 01, 2009 | Honda Accord Cars & Trucks

1 Answer

Remote won't lock driver's side door lock


replace the lock actuater in the drivers door and you can try your local library for a diagram and pictures if you need them

Mar 20, 2009 | 2000 Volkswagen Passat 4Motion

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2007 Hyundai Santa Fe Limited Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...