Question about 1985 Ford F150

1 Answer

How to remove oil pan on 1985 f 150 4 wheel drive

How to remove the oil pan?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,070 Answers

Which engine?

Posted on Apr 17, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2309 Answers

SOURCE: how do i remove the oil pan off a 92 e-250 2 wheel

you may be able to get it off by removing the oil pump,

Posted on Nov 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove an oil pan off a 1998 ford 2 wheel drive with out pulling the engine


Remove the bolt that runs thru the engines motor mounts, not the ones that attach it to the engine block. Take a 2x4 and put it on a floor jack so the jack won't damage the front pulley. Raise the engine with the floor jack to get enough clearance to manuver the pan around the steering components once thw oil pan bolts have been removed. Watch the fan blades don't hit the radiator.

Mar 09, 2015 | Ford Cars & Trucks

2 Answers

How do i remove the oil pan to get to the oil pump on a 1992 chevy s10 pickup 4x4


pick your battles cause your really going to have a ruff time of it. chassis in the way for the most part. you choose best way for you to do it.

May 24, 2014 | 1992 Chevrolet S-10

1 Answer

Change oil pump


What you really want to do is have a technician remove the oil sending unit and attach a pressure gauge of known reliability. Only then can you know if your pressure is good or bad.

If you have to change an oil pump, you can have problems reaching it. You may be able to find a Video or text online for your exact model. The Capri series covers a lot of Years and the engines may be different and one year may be a front wheel drive while an older one may be rear wheel drive.

One of the biggest problem is having clearance to remove the oil pan. Sometimes in the closest clearances turning the crankshaft can help make room to drop the oil pan.

Front wheel drive units can have a cradle which blocks pan removal. You need to find out the requirements for your exact year.

The pressure test will help diagnose other problems. Bad bearings can leak so much oil that pressure will behave exactly like you describe.

Feb 06, 2014 | Mercury Capri Cars & Trucks

2 Answers

There are two plugs underneath when changing the oil. Which one do I pull. The front one or the rear one?


This is an 03 Mountaineer? What engine? It has two plugs on the oil pan? They did this on some of the the old 5.0 engines.

Dec 28, 2010 | 2003 Mercury Mountaineer

1 Answer

Best way change oil pump in 1999 dodge durango


You have to remove the oil pan. It is different for 2wheel drive and 4 wheel drive. In either case, you have to jack up and support the engine. Most of the time you must also remove the transmission rear mount so you can jack up the transmission also in order to get enough clearance to get the pan out between the transmission bell housing and the frame crossmember.

On 4X4 vehicles, you must also first remove the skid plates and the front drive axle to get the oil pan off.

Dec 13, 2010 | 1999 Dodge Durango

1 Answer

How to replace oil pan on a 1995 geo tracker 4 wheel drive


1 Raise and support
2 Remove front diff assembly from chassis
3 Drain oil
4 Remove clutch or torque converter housing lower plate
5 Remove oil pan

OIL PAN BOLTS 6.7 - 8.9 ft.lb
OIL PRESSURE SWITCH 10 ft.lb


Mar 11, 2010 | 1995 Geo Tracker

2 Answers

I need to change the oil pan. what is proceedure?


support front of vehicle, drain oil and return to oil recycling center (walmart) remove both (right and left) motor mounts and transmision linkage, transmision support bars( if needed for extra clearance ) unbolt oil pan. carefully lif engine from frame, taking care not to hit and break anything when the engine gets too close to your firewall. you should then be able to remove and replace oil pan. you'll need the bolt tightening pattern and torque specs for your vehicle. hope this helps

Oct 27, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

1 Answer

How can i get the oil pan out on a 2001 chevy malibu?


2.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan


  1. Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm).
  2. Accessory drive belt
  3. Negative battery cable

  4. Fill the engine with oil to the correct level.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan

To install:
  1. Apply a 0.13 inch (3.5mm) bead of the GM P/N 12378521 sealant around the perimeter of the oil pan and oil suction port opening.
  2. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).

    0900c1528024bb26.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Oil pan bolt sequence-2.2L engine
    Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm). Accessory drive belt Negative battery cable
  3. Fill the engine with oil to the correct level.
3.1L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Evacuate and recover the A/C system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    WARNING DO NOT disconnect the refrigerant lines or allow the compressor to hang unsupported.


    Negative battery cable Accessory drive belt Upper and lower radiator hoses Right front wheel Inner fender splash shield Antilock Brake System (ABS) Wheel Speed Sensor (WSS) electrical connector Right front ball joint from the steering knuckle Right side outer tie rod end A/C compressor bolts and move the compressor aside


    Evaporator-to-accumulator A/C line Flywheel cover Engine cradle bolts Crankshaft balancer Starter motor Oil pan

To install:

0900c1528024bb27.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the oil pan mounting-3.1L and 3.5L engines

  1. Install or connect the following:

Sep 02, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...