Question about 2007 Ford F-250 Super Duty

1 Answer

Brakes both frnt&rear calibers hanging up but not all the time

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,682 Answers

Duplicate question.

Posted on Apr 18, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brake system all new but pedal goes to the floor


double check the brake master cylinder and brake piston cylinder.

Mar 11, 2015 | GMC Sierra Cars & Trucks

1 Answer

Rear brake calibers


Open bleeder valve & push piston in by hand

If you have an internal parking brake, that has
to be screwed in also

Jan 22, 2013 | 2008 Dodge Grand Caravan

1 Answer

How do you change the rear brakes pads and a caliper on a 2004 XJ8?


you will need to 1st get a caliber turning set from harbor freight, it very cheap maybe 35-40 bucks...you need to raise both rear tires,crank the car put it in neutral so that the electric module releases the brakes from park position,then you disconnect the neg battery term.remove the tires, open the hood,remove the fluid reservoir cap,remove the calibers by the two bolts facing the inside,then remove the pads,then take the caliber tooland lock the two male nipples ends inside the female piston plates(u will see how the fit)now make sure the brace plate of the of the caliber tool is snug and begin turning the tool threaded side clockwise,and the bolt near the plate should be turned counter clockwise and each turn will turn the piston inside the caliber until its all the way flush with the inside of the caliber wall itself...then place the pads inside the caliber rotors are the same as removing from any other car,they may need a good tap with a hammer,some may have one alen head screw.But replace the rotors and pads.Once they are replaced,lower the car,reconnect the neg terminal,put the fluid cap back on,crank the car,pump the brakes and hold the center console lever upuntil the brake light goes off and u will hear the rear brake module engage.Hope this helps!

Sep 28, 2011 | 2004 Jaguar XJR-Series

1 Answer

2003 s type brake front pad - what tools are need to change the pads


the front pads are pretty straight forward,just a c clamp is sufficient to press the calibers,make sure the brake fluid reservoir cap is off when you do them..just unbolt the calibers from the rotors and they work the same as standard brakes,but the rear calibers at time will need a caliber tool to turn and press the piston simultaneously

Sep 03, 2011 | 2006 Jaguar X-Type

1 Answer

Replace rear rotors 2004 jeep cherokee


Heres what you will need to do this type of job. First you will need a rachet and metric sockets with an extention if available. Also you will need somthing to press the caliber piston back into place a special tool or some kind of press would work . A plastic auto hammer to knock the rotors loose, somtimes they can be difficult to remove. Pliers would be needed as well as a screw driver to help mount the caliber or pads back into place. One thing to keep in mind is that if you indeed are replacing the rear rotors, it is recommended to get new pads as well. This is for the reason that old pads will cause break sqealing since they are not surfaced perfectly straight for the new rotor. Step one will be to get the caliber of the vehicle so if there is a medal clip on one of the studs just use the pliers to rip it off. Then use the rachet to remove two bolts holding the caliber. After you remove those bolts, there should be another two bolts holding the caliber bracket as well, do the same procedure in removing those. IMPORTANT do not let the caliber hang by the brake cable, put it on a stand or in a location where it is not free fall hanging. Now you should just have the rotor left, try pulling on it to see if it breaks loose, if not then use your plastic hammer to bang in the back of the rotor and knock it loose that way. If I remember correclty those rear rotors will have brake shoes underneath. Do not wory about those they are there for your emergency brakes. Now put the new rotor on and make sure it is securley installed on the wheel hub. Install you'r bracket first, then begine to install your caliber back into place. NOTE the caliber may not install to easy onto the rotor for the reason that you will need to compress the piston inside with either the special tool or some type of press. If you compress it and you hear brake fluid dripping down, it is nothing to worry about, its just the fluid being pushed back by pressure. Install the caliber and pads the same way as removal paying close attention to the other side if your not sure of how the originally were installed. When all this is finished look up brake bleading on YOUTUBE.com to accurately bleed your brakes and remove any air inside that may cause spongy or moister inside your brake lines.

Hope this Helps!

Jun 07, 2011 | 2004 Jeep Grand Cherokee

1 Answer

When I go to stop the van pulls to the right then when I let off the brake pedal it pulls left.I rebuilt the driver side caliper but the piston is still hard to push back into the caliper. I checked the...


Replace both calipers, much easier..... your description indicates to me that your left caliper is hanging ON, overheating and when brakes are applied, the right caliper (not overheated) is more efficient than the left one......

ALL brake work must happen to BOTH SIDES, on that axle set, every time (meaning both front or both rear). Anything else just makes problems

Oct 10, 2009 | 1991 Dodge Ram 350

2 Answers

Rear breaks on 2007 caliber


It's hammer time! Give it a few cracks around the face, 12:00 then 6:00 then 3:00 then 9:00. If it's not off by then your not hitting it hard enough.

Jul 01, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

4 Answers

Brakes need to be bled


Back to front.....rear passenger first then rear driver's....then pass front and then driver's last.

Jun 25, 2009 | 1991 Toyota MR2

1 Answer

Rear right brake locks and studders


Get your caliber replaced and if it still has the factory rotor also get that replaced. Recommended to get both replaced at the same time.

Jan 10, 2009 | 1997 Pontiac Sunfire

2 Answers

2007 dodge grand caravan


according to the service manual there are two bolts hold the caliber to tthe adapter plate and the caliper should roll up and out. the only problem i could imagine is if the pads are hanging in the adapter

Nov 21, 2008 | 2005 Dodge Grand Caravan

Not finding what you are looking for?
2007 Ford F-250 Super Duty Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...