Question about 2001 Chrysler Concorde

Open Question

Where to find the bad blend door actuator on a 2001 chrysler concorde

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pumpkinman
  • 1147 Answers

SOURCE: how do i fix a 2001 chrysler concorde door handle

Youll have to pull the door panel to access the handle, once you have you can easily remove and replace it.

Posted on Oct 15, 2009

Ad
jturcotte
  • 8578 Answers

SOURCE: location of blend door or

The temperature door actuator is located at the bottom of the heater housing at the center terminal. It looks like this:

6b48b5c.gif
To remove the actuator

  1. Remove the left and right underpanel silencer ducts.
  2. Remove the two retaining screws from the actuator which are accessible from the right side of the center stack.
  3. Remove the screw from the actuator on the left side.
  4. Pull the actuator straight down from the shaft and disconnect the electrical wire. Upon removal, matchmark the shaft position of the actuator, because the shaft on this motor is keyed.

Posted on Oct 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 chrysler concorde. Heater blows only warm air. Replaced water pump thermostat and had radiator flushed. What is the problem


This is most likely being caused by a defective air temperature control blend door and or actuator. This part moves back and forth deep inside the HVAC ducting to divert air across the Heater core or the AC Evaporator core, when they fail or stick they can create this issue.

Oct 12, 2016 | 1999 Chrysler Concorde

1 Answer

What do i do to get my 2002 Chrysler Concorde to blow heat?


Check the temp of the two hoses going to the heater core, one should be hotter then the other, if they are both the same of very little difference you have no flow through the core, if there is a heat control valve in the supply or return line it could be bad, or has a vacuum leak so its not actuating if not the core is probably plugged, or could be leaking, but usually you will smell the fluid and/or see a wet spot on the floor.

Mar 02, 2015 | 2002 Chrysler Concorde

1 Answer

Replace blend door in 07 Chrysler sebring


The most likely problem is either the blend door actuator or a broken blend door itself.
Both are only accessible by complete removal of the instrument panel(dash).
The blend door actuator can be tested with a Chrysler factory scan tool hooked up to the DLC(data link connector). If blend door actuator is working when tested with the factory scan tool, then blend door itself is at fault.
The only other way to test the blend door actuator is to test for 12v at connector, but you would have to remove the instrument panel in order to gain access to the actuator

Dec 24, 2014 | Chrysler Cars & Trucks

1 Answer

2001 chrysler town and country. A\C heat Blowers will not work when controlled my front main pannel. It is a auto temp controlled system. The rear blower will work but no heat when controlled by the rear...


Hi,
This may be similar to what I just fixed on an '00 dodge:
http://www.dodgeintrepid.net/showthread.php?t=89711

Accessing the Integrated Diagnostic System:

Procedure for Automatic Temp Control (ATC) equipped vehicles:

With the engine ON and the vehicle stopped set the temp to 75*F. Next hold down the Floor, Mix and Defrost buttons until the ATC display begins to flash. While the display is flashing, the system will run it's tests and calibrations.

When the display stops flashing, the tests and calibrations are complete.

The ATC display can only display one error code at a time. Any stored codes can be scrolled through by pressing the Panel mode button once for each code. DO NOT press any other button or you will have to start the test over. Note the codes and refer to the list below to determine what system is malfunctioning.

List of Climate Control DTCs:
23: Blend door actuator feedback failure (bad servo)
24: Mode door actuator feedback failure (bad servo)
25: Ambient temp sensor failure
26: ATC In Car thermister failure (ATC only, bad ATC head or ATC head disconnected while battery is connected)
27: ATC in car sensor failure (ATC only)
31: Recirculation door actuator stalled (stuck door or bad servo)
32: Blend door actuator stall failure (stuck door or bad servo)
33: Mode door actuator stall failure (stuck door or bad servo)
34: Engine temperature message not received (ATC only, bad ATC head or bus failure)
35: Evaporator sensor failure
36: ATC control communication failure (bad ATC head or bus failure)
37: Blend door actuator output shorted to battery (bad servo or wiring fault)
38: Blend door actuator output shorted to ground (bad servo or wiring fault)
39: Mode door actuator output shorted to battery (bad servo or wiring fault)
40: Mode door actuator output shorted to ground (bad servo or wiring fault)
41: Recirculation door actuator output shorted to battery (bad servo or wiring fault)
42: Recirculation door actuator output shorted to ground (bad servo or wiring fault)
43: Common door shorted to battery (probable wiring fault, could be a servo that failed in an odd manner)
44: Common door shorted to ground (probable wiring fault, could be a servo that failed in an odd manner)
45: A/C control blend door input open or shorted with respect to ground (MTC only, wiring fault or bad servo)
46: A/C control blend door shorted to battery (MTC only, wiring fault or bad servo)
47: A/C switch failure (MTC only)
48: A/C control mode door input shorted to ground (MTC only, wiring fault or bad servo)
49: A/C control mode door input shorted to battery (MTC only, wiring fault or bad servo)
50: A/C control electric backlite (EBL) switch fails (MTC only)

51: System voltage too low for calibration!!! (check battery cables, battery and alternator!)

Dec 10, 2014 | 2001 Chrysler Town & Country

1 Answer

I have a 2001 chrysler voyager where is the blend door actuator located and how to remove it


its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.
  1. Disconnect and isolate the battery negative cable.
  2. Remove first row seat.
  3. Remove second row seat.
  4. Remove sliding door sill trim panel.
  5. Remove quarter trim bolster.
  6. Remove D-pillar trim panel.
  7. Remove first row seat belt anchor.
  8. Remove second row seat belt anchor.
  9. Remove screws attaching quarter trim to quarter panel from bolster area.
  10. Remove screws attaching rear edge of quarter trim to attaching bracket.
  11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
  12. Remove quarter trim from quarter panel.
  13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
  14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
  15. Pass first row seat belt through slot in trim panel.
  16. Remove quarter trim panel from vehicle.
  17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
  18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
  19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
  20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
  21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
  22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
  23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
  24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

May 21, 2014 | 2001 Chrysler Voyager

1 Answer

Heater won't turn off when it is turned off


Usually a sign of a faulty blend door actuator under the dash. The blend doors direct air thru the heater core and vents.

Dec 05, 2012 | 2002 Chrysler Concorde

1 Answer

Location of blend door or actuator on chrysler concorde 94 ?


The temperature door actuator is located at the bottom of the heater housing at the center terminal. It looks like this:

6b48b5c.gif
To remove the actuator
  1. Remove the left and right underpanel silencer ducts.
  2. Remove the two retaining screws from the actuator which are accessible from the right side of the center stack.
  3. Remove the screw from the actuator on the left side.
  4. Pull the actuator straight down from the shaft and disconnect the electrical wire. Upon removal, matchmark the shaft position of the actuator, because the shaft on this motor is keyed.

Oct 03, 2010 | Chrysler Concorde Cars & Trucks

1 Answer

How do i fix a 2001 chrysler concorde door handle


Youll have to pull the door panel to access the handle, once you have you can easily remove and replace it.

Oct 15, 2009 | 2004 Chrysler Concorde

1 Answer

2000 chrysler concorde switch unlocks but wont lock doors.


sounds like the actuator. I had the same problem. Mine got to the point where it will now only work with the key. Had it looked at by dealer.. actuator is bad. Good luck.

Apr 17, 2009 | 2000 Chrysler Concorde

2 Answers

Will only blow cold air , sometimes it will blow hot


sounds to me like a blend door problem or blend door actuator problem

Mar 03, 2009 | 1998 Chrysler Concorde

Not finding what you are looking for?
2001 Chrysler Concorde Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...