Question about 1996 Honda Accord

1 Answer

How to pre bleed the master cylinder on my 1996 honda accord 5 speed

Replaced master clutch cylinder on my 1996 Honda accord how do I pre bleed the master clutch cylinder

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 70 Answers

There are different ways to bench bleed the master depending on the tools available to you... did you receive a fitting, with or without a port for a small hose, in the new master box? if not then you should make one or get one at the parts store. you need to put the master in a vice (from the mount, not the body) and fill it with fluid. this is where the fitting comes in handy, you are going slowly depress the piston about half way at first having the fluid that comes out the port directed back into the reservoir with a hose. keep the hose submerged. if a vice and fittings are not available, you can mount the master in the vehicle, connect the line and fill with fluid. disconnect the line from the slave cylinder and submerge it in a container. press the pedal by hand slowly. make sure the line stays submerged and the master is never run dry. if everything is kept clean, you can reuse the fluid from the catch container.

Posted on Apr 17, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

virgils
  • 39 Answers

SOURCE: replacement a speed sensor for a honda accord 1995 Problems

Is this a wheel speed sensor for an ABS system? or a Vehicle Speed Sensor? I will assume it is a VSS for right now
the VSS is located on the transmission, you will need to remove the intake to see it more clearly but here is a picture that shows the unit and its components http://econtent.autozone.com:24991/znetrgs/repair_guide_content/en_us/images/0900c152/80/05/f9/9e/small/0900c1528005f99e.jpg

Posted on Oct 11, 2008

  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

TheAsian
  • 93 Answers

SOURCE: i need 1996 honda accord speed sensor plug wiring diagram

Diagram is courtesy of honda

[IMG]http://i34.tinypic.com/10wjogi.jpg[/IMG]

Posted on Dec 09, 2008

TheAsian
  • 93 Answers

SOURCE: Connector for Speed Sensor on1996 Honda Accord Auto Trans.

If you are talking about just plugging into the speed sensor yes. A VTEC and NON-VTEC are one and the same.

Posted on Dec 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed clutch master cylinder on a 1995


It takes 2 people. Open the bleeder on the slave cylinder, hold your finger over it while the pedal is pumped, releasing the pressure when the pedal is down.. Once it starts pushing fluid thru, close the bleeder, pump 3 times, open bleeder with pedal down. Repeat till clutch feels good. If you are replacing the master cylinder, bench bleed it 1st. Be patient, this all takes awhile.

Sep 30, 2014 | 1995 Honda Accord

1 Answer

Cant locate clutch cylinder 1988 Honda accord lx 5 speed trasmssion


If it is a hydraulic clutch, and not cable operated, there will be two cylinders. A clutch master cylinder will be mounted on the firewall next to the brake master cylinder. One steel line will go from the master cylinder down to the slave cylinder bolted onto the transmission housing where the clutch lever extends out of the housing. Other than bleeding the slave cylinder, no adjustments are necessary on hydraulic clutches. Cable operated clutches have an adjusting mechanism to take up slack when the clutch disc wears. The adjuster will be inside the engine bay.

Sep 22, 2013 | 1987 Honda Accord

1 Answer

1996 honda accord 5 speed transmission stuck in gear


Let's look at your slave cylinder and your master cylinder.
Under the hood of your car are two master cylinders, and physically, they are close together.
They are found right in front of you as you drive the car, except they are under the hood and about chest high.
My 1990 has them right along side one another.
The brake master cylinder reservoir is about 4 inches in diameter, the clutch master cylinder reservoir is about 3 inches in diameter. Both of them take quality brake fluid.
Sounds like your clutch master cylinder is dry of brake fluid.
It would be nice if all you had to do was to add brake fluid to the "fill" line, but then you'd have air in that system, and it would need to be "bled" to work.
If you do find the brake fluid low, very likely the slave cylinder needs replacement, as your car is the right age to need this.
Be blessed.

Mar 18, 2013 | 1991 Honda Accord

2 Answers

I have a 96 honda accord and changed the clutch master cylinder and the slave cylinder and bled the system there still is no clutch pressure


You need to PRE BLEED the master cylinder, or you may never get pressure. Parts houses sell little hoses for this purpose.

May 30, 2010 | 1996 Honda Accord

1 Answer

Bleeding Clutch Cylinder with no bleeder screw


I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Jun 04, 2009 | 1996 Honda Accord

1 Answer

1996 honda accord clutch goes all the way to the floor


check the slave and clutch master cylinder for leakage. look under the dash , at the clutch master) push rod attached to the clutch pedal) . try to see if there are any leaks around it. if so have it replaced and have the system bled to remove all fluid and air stuck in the system.

Apr 04, 2009 | 1996 Honda Accord

2 Answers

1991 honda accord 5 speed


Sounds like you have a clutch problem. first thing to check is the fluid level in your clutch master cylinder, which is near your brake master cylinder for fluid level. It uses same fluid as brakes. See what you find out & get back if need more help.

Jan 23, 2009 | 1991 Honda Accord

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

1 Answer

Bleeding clutch slave cylinder


if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Aug 05, 2008 | 2001 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...