Question about Jeep Liberty
You lift out , all by self>?
or only clicks, when you , push the fob open button, or door switches?
Posted on Apr 18, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2006 jeep liberty will not
The ORVR (On-Board Refueling Vapor Recovery) system consists of a unique fuel tank, flow management valve, fluid control valve, one-way check valve and vapor canister.
The ORVR (On-Board Refueling Vapor Recovery) system is used to remove excess fuel tank vapors. This is done while the vehicle is being refueled..
Fuel flowing into the fuel filler tube (approx. 1 inches I.D.) creates an aspiration effect drawing air into the fuel fill tube. During refueling, the fuel tank is vented to the EVAP canister to capture escaping vapors. With air flowing into the filler tube, there are no fuel vapors escaping to the atmosphere. Once the refueling vapors are captured by the EVAP canister, the vehicle's computer controlled purge system draws vapor out of the canister for the engine to burn. The vapor flow is metered by the purge solenoid so that there is no, or minimal impact on driveability or tailpipe emissions.
As fuel starts to flow through the fuel fill tube, it opens the normally closed check valve and enters the fuel tank. Vapor or air is expelled from the tank through the control valve and on to the vapor canister. Vapor is absorbed in the EVAP canister until vapor flow in the lines stops. This stoppage occurs following fuel shut-off, or by having the fuel level in the tank rise high enough to close the control valve. This control valve contains a float that rises to seal the large diameter vent path to the EVAP canister. At this point in the refueling process, fuel tank pressure increases, the check valve closes (preventing liquid fuel from spiting back at the operator), and fuel then rises up the fuel filler tube to shut off the dispensing nozzle.
Posted on Dec 23, 2008
You need to tighten the lock mech on the boot lid. this will close the boot just enough more to turn the light on. It's no biggy, you might need a star driver depending on bolt head. move it into the boot lid approx 4mm to start. then 1mm until 10mm. if no joy then it may be the sensor.
All the best
Posted on Jul 25, 2009
you have two relays on the interior fuse block one for locking and one for unlocking. Swap them and see if the problem is now such that they will not lock. If so you have your answer.
Posted on Aug 30, 2009
Tips for a great answer:
Jul 11, 2014 | 2005 Jeep Liberty
Jun 09, 2014 | 2006 Jeep Liberty
Mar 21, 2014 | Jeep Liberty Cars & Trucks
Feb 18, 2013 | 2006 Jeep Liberty
Doors not getting open with remote or key problem,there are help
links provided below.Click the link below to go through its
procedure and troubleshoot the problem:----
drivers side front door will not open from inside or outside?
Car door will
All power door
locks not working ?
Door lock Actuator?
How to Access car door panel?
Vehicle door panel components?
Truck Door will not close?
Where is Cars Door control Module located?
Power door locks not working?
Door ajar light stays on?
Door locks not working?
Front Door dis-assembly diagram?
Rear Door dis-assembly diagram?
How to test Power door locks?
Doors will not open with Remote?
How to replace
Door Hatch ?
How to remove Doors?
How to Replace Doors?
not unlock Rear door?
Door locks or windows not working on car?
This will help.
Feb 14, 2012 | 2002 Jeep Liberty
Mar 20, 2011 | 2006 Jeep Liberty
May 11, 2010 | 2006 Jeep Liberty
Apr 04, 2009 | 2002 Jeep Liberty
67 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: