Question about 1991 Toyota Camry

1 Answer

Power windows, blower, temp and fuel guages only work when I reverse and pushing the brake pedal

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

You seem to have faulty wiring and possible relay issues. I would visually check harness under steering wheel. the connector could have been stuck behind brake pedal.

Posted on Apr 17, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: no brake lights when brake pedal is pushed

check first wirring is work properly, and check lamps are work properly. If not then change lamps.If works properly then check connectors, and paddle switches are work properly. If not then change the connector and paddle switches.

Posted on Aug 26, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuck in park,power windows don't work,reverse lights don't work dash doesn't work. keeps blowing 10 amp fuse for reverse lights.changed brake pedal switch didn't help


of course changing a brake pedal switch will not help in a reversing light problem
they are two totally different circuits
check for a damaged wire at the reverse light switch or bulb holder for the reversing bulbs for a dead short
as for the rest check the IGN fuse under the bonnet

Feb 18, 2016 | 1997 Honda Accord

2 Answers

Reverse lights/Rear internal brake light not working


there is a reverse switch on top of the trans where the shift cable is attached. is there power to and through that switch while in reverse? the cyclops light needs the power interruption traced back from the socket to the switch on the brake pedal to find out where you have lost power or possibly taped into brake power at another brake light bulb socket

Mar 31, 2014 | 1988 Toyota Camry

3 Answers

1990 geo prizm brake lights only work when car is off


in front were the brake is try to c if there is a guage like a small little wire

Nov 16, 2011 | 1990 Geo Prizm

1 Answer

I have to push very hard on the brakes to come to coplete stop. The master cylinder is fine and the brakes have been bled at the calipers. I have heard There is another place to bleed the brakes. Where...


CHECK POWER BRAKE BOOSTER.WITH ENGINE OFF.DEPRESS BRAKE PEDAL SHOULD BE FIRM.NOW START THE ENGINE BRAKE PEDAL SHOULD DROP A LITTLE AND HOLD IF BRAKE GOES TO THE FLOOR POWER BOOSTER COULD BE BAD.I STILL SAY YOU HAVE AIR IN BRAKE SYSTEM.YOU NEED TO BENCH BLEED BRAKE MASTERCYLINDER AND BLEED FRONT CALIPERS AND REAR BRAKE CALIPERS. BY YOUR CAR BEING ABS BRAKES SYSTEM BEST TO LET DEALERSHIP FIX BRAKES. THEY HAVE TO USE DIAGNOSTIC EQUIPMENT TO RESET ABS BRAKE HYDRALIC CONTROL UNIT AND PRESSURE BLEED THE BRAKE SYSTEM. IF BLOWER MOTOR KEEP RUNNING YOU HAVE FAULTY BLOWER MOTOR RELAY.IF BLOWER MOTOR HAS ONE SPEED CONTROL.YOUR BLOWER MOTOR RESISTOR BAD OR AC AND HEATER CONTROL SWITCH IS BAD.

May 13, 2011 | 1998 Dodge Intrepid

1 Answer

I have a 1997 bmw 318ti. on board computer


Hmmm. The unit that calculates the fuel is under the back seat base. There are two level sensors under covers on either side. Could be that you have a trapped wire shorting and when you go into reverse the back axle just momentarily jogs the shorted wire. I'd look at the wiring there.

Mar 25, 2010 | BMW 318 Cars & Trucks

1 Answer

1994 Pontiac Grand Am Its sat about 2 months now. I went out to start it. It was dead. So I jumped it. Well I got it started and the check engine light and abs light was on. Well I put my foot underneath...


If the battery is bad and not holding a charge, every time you push on the brake's. The break lights come on and puts a load on the electrical system and if the voltage drops below 10.5 volts, the ECM will shut down fuel injector and ignition system. The other thing to is that the fuel pressure may be dropping due to the electric fuel pump not getting enough volts every time you put on the brakes. You cold always try keeping the jumper cables connected to make sure it's the voltage drop that is causing the engine to stall. Keep me posted, be glad to help you get your car running 1005 again soon.

Nov 07, 2009 | Pontiac Grand Am Cars & Trucks

1 Answer

Gas guage and water temp gauge do not work clock works alt works oil works guages work just not gas and water temp ?????


On the rear of the instrument cluster there should be a resistor. This is how the fuel and temp guages are limited to a certain voltage decreasing the power to them so that they dont burn out. These (voltage limiters) resistors are available seperately from the dealership.

Oct 04, 2009 | 1987 Jeep Wrangler

1 Answer

Blower fan has no output. Temp guage not working


for blower motor check fuse hvac 20a int.panel and hvac 30a fuse in elect.center eng.compartment,if ok,check for 12v at blower connector if power is there fan is defect..temp.gauge check connection at unit if ok check resitance if it varies when engine warms up,if it doesnt vary replace unit,if it varies check wiring circuit,unit is place at drivers side of eng.block near sprk plugs.for hard to start;if check eng.light is not on could be in need of a tune-up depending on how long ago it was done,if check eng light is on or was on scan ecm for trouble code.

Oct 03, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1991 Toyota Camry Logo

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...