Question about 2007 Honda CR-V

1 Answer

Handbrake cable pulled on the lever and something snapped, the lever is now loose.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Honda Master
  • 796 Answers

Check under car and at inside of each rear wheel where cable goes into to see if the emergency cable broke. good-day!

Posted on Apr 17, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace my hand brake cable on my ford falcon XH ute


wait a bit ....is it rear disc or rear drums on that ute

will assume its under dash hand brake pull lever tyoe

the disc setup may have single cables for each rear
rear disk brake cable is approx $ 150

if your XH it is close to the XE and XF set up drums
a complete one line loop cable outer and inner
with plastic grommets along the back chassis rail ( they break )
so the one inner cable works both rear handbrake shoes


hand brake cable is a shorty

undo the adjustment thread
just below the hand brake cable point up somewhere above the gearbox
(drums )
after new cable fitted
drums are adjusted with the old school way with the handbrake adjuster tool
handbrake cable adjusted

then the handbrake handle when pulled out to hold needs14 plus clicks
comes out a long way for some weird reason
on drums
if cable adjustment is done wrong onrear drums the handbrake cable will come loose in the drum as you drive along

26261095-l1jraapkfcyxqeqgczv0cruv-4-0.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-3.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-5.jpg

Aug 17, 2016 | Ford Cars & Trucks

2 Answers

Hand brake adjustment on KIA Carnival


The Kia Carnival has drum brakes on the rear and they are self adjusting. They can however be adjusted by working the handbrake lever up and down a few times, if it has not been previously adjusted by using the cable adjustment, then this will probably not work, and it is something I come across quite a lot. if all this fails, then it is a matter of taking the wheels off and removing the drum. firstly check the position of the handbrake actuating lever (its connected to the cable) with the handbrake off (wheels chocked of course) the lever should be as far back as possible to the brake shoe, if it isn't check that you have a little bit of slack on the cable and it is not seized if not adjust the cable off a little so the levers return fully. if you look you will see the self adjuster you can turn the notched wheel a few clicks and then put the drum back on. make sure it is not binding when you turn it (a slight rub is ok) tap the drum (top, bottom, left, right) to centre the shoes (this is important because it will give false adjustment if you don't). once you have done this to both sides, double check both wheels are still running free. replace wheels a try handbrake, it should be ok now. Check how many clicks you need to pull the lever to apply brake and adjust the cable just enough to remove any slack in it, NO MORE. Warning! DO NOT HIT THE DRUM HARD AS IT WILL CAUSE FRACTURES. I hope that has been of some help to you.

Oct 26, 2014 | Kia Carnival Cars & Trucks

1 Answer

Handbrake lever no tension


lf you follow the route of the cables under the car then pull on the left and right outer cables one or the other should come apart failing that it will probably be a break in the handbrake lever....Hope this help`s..

Dec 31, 2012 | 2000 Ford Focus

2 Answers

How to adjust handbrake


Do check the rear brakes but below is some help as far as adjusting the cable the proper way. Per specs after all is done your parking brake should be correct as you pull up the lever after 4 - 8 clicks. Hope this helps....

1_24_2012_10_54_13_am.jpg1_24_2012_10_54_32_am.jpg1_24_2012_10_55_39_am.jpg1_24_2012_10_55_55_am.jpg

Jan 24, 2012 | 1997 Honda Accord

2 Answers

My handbrake needs adjusting in my Toyota Corolla 1994. Can u please explain how this adjustment is done.


Hello, My usual Brands are Ford products, but Foreign cars usually use simple, less expensive ways to do things. Assuming the brake pads are good, there should be a cable connected to the handbrake. You would usually pull the handbrake up to engage about 1/4 the way to engagement and lock it there.
Then you would go underneath the car and find the cable that stretches from the handbrake lever to a juction with a second cable. There should be an adjusting thread somewhere at this intersection.

With the rear wheels off the ground, you would tighten the nut on the threads of the handbrake cable until you hear rubbing in the rear brakes. Then get inside the car and pull back on the handbrake lever and you should not be able to move the rear wheels with the handbrake set. You then release the handbrake 100% and the rear wheels should turn mostly without noise.

Now if you can not find an adjustment nut under the car, it is possible the handbrake adjustment nut is under the handbrake cover/boot inside the car. Still use the same process of setting the lever 1/4 engaged and tightening the threaded cable until the rear wheels start dragging.

I hope this helps you.

Sep 28, 2011 | 1994 Toyota Corolla

1 Answer

Ford bantam handbrake adjustment


remove the back brake drums ,slacken handbrake cable then run a mini grinder around the lip on the edge of the drum .Then adjust the auto adjusters manully so when the drum is push on it just goes on ,tap with a hammer all around the drum to level the shoes and if need be adjust up a bit more ,then when finished re-adjust the cable so you have three notches on handbrake lever

May 31, 2010 | 2006 Ford Focus

1 Answer

How to adjust handbrake cable


HANDBRAKE CABLE ADJUSTMENT

1. Raise the vehicle and release the handbrake.
2. De-adjust the handbrake cable.
  • Remove the locking pin.
  • Slacken the adjuster locknut.
  • Slacken the adjuster until the levers on the callipers have returned to their stops.
3. Paint alignment lines on the lever and caliper
4. Tighten the adjuster until the caliper levers move from the alignment lines.
5. Apply the handbrake to equalise the cable.
6. Tighten the adjuster locknut to a minimum of three clicks and a maximum of six clicks.
7. Fit a new adjuster locking pin.
8. Lower the vehicle.

Jun 04, 2009 | 2002 Toyota MR2 Spyder

2 Answers

Pt cruiser parking brake ajustment


Hello,
It is manual adjustable.

Here is the photo where you can find it ("saatoruuvi"= "adjustable srew")

http://www.ptcruiser.fi/ptgalleria/albums/userpics/Jarrukengat.jpg

Apr 20, 2009 | 2001 Chrysler PT Cruiser

1 Answer

Mercedes E300 1999 handbrake probelem


hi,it has a cable,lift your car,seem your cable is jump in to the rail,or disconnected from two rear wheel,ty

Mar 10, 2009 | 1999 Mercedes-Benz E-Class

2 Answers

Volvo s40


The handbrake adjuster is under the centre console behind the lever. If its coming too high, check that the levers at the rear brake calipers are free and moving back to their stop position - they are prone to seizing up on older or little used cars. They can usually be freed off with a bit of lube and working the lever back and forwards. If that dosn't work, unfortunately you'll need new calipers. Do not adjust the handbrake cable unless the caliper levers are at their stops as this seriously reduces handbrake efficiency!

Jan 08, 2009 | 2000 Volvo S40

Not finding what you are looking for?
2007 Honda CR-V Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...