Question about 2007 Hyundai Getz 1.3

Open Question

Replace the top central brake light bulb on my Hyundai Getz 1.4 model 2007

All I can see is a plastc cover with no obvious retainers. I don't want to prise it off in case I break the cover.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 566 Answers

SOURCE: 2007 Hyundai Santa Fe - Replacing fog light

hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Posted on Oct 28, 2008

Ad
  • 1 Answer

SOURCE: How do I change the back brake light of a Hyundai Elantra?

If it is the light in the rear window, there are two plastic caps on either side on the base of the light. Pop off the cap and remove the screws inside. That should allow you to get to the bulb. I went to autozone for the bulb w/o removing it and they gave me the wrong one. If you have the bulb removed, you're better off, if not, the people at advanced got me the correct one without any issues. If it's the brake lights on the back of the trunk, you access those from inside the trunk. On either side, there are thumbscrews (sometimes under the fabric lining flaps). Once you remove the bulb carrier, you'll know which one is out. It usually lines up with the red cover but if you can borrow someone's time, have them look in your trunk at the bulbs as you test your parking lights to see which one lights and which one doesn't. Hope this helps.

Posted on Dec 26, 2008

ghost4548
  • 776 Answers

SOURCE: hyundai getz radio

Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg

Posted on Jun 05, 2009

  • 2 Answers

SOURCE: how to change hyundai getz brake light in light cluster?

On the Getz remove 2 screws on the outside then gently prise the cluster off from the dowels as above.

Posted on Aug 26, 2009

johnjohn2
  • 5763 Answers

SOURCE: How do you replace the brake sensor switch located

just un plug it and twist out.install new and adjust.

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2007 Hyundai Getz with 38.000 on clock has oily film over engine


could be from a leaking rocker cover gasket at the end of the rocker shaft, loose rocker cover or oil filler cap not properly installed
check operation of the PCV valve to reduce crankcase pressure that may be contributing to the problem

Jun 15, 2016 | 2007 Hyundai Getz 1.6

1 Answer

How to change stop light globe on 2008 hyundai getz


Remove the two 10 mm (head) bolts that hold the stop light. This bolts are between the tail light assembly and the tail gate weatherstrip. You can see them without having to remove anything.

By using a masking tape wrapped flat screwdriver, pry "back" the whole tail light assembly. Once out, you can twist the brake light (or reverse, or turn signal) bulb plug, remove and replace the bulb.

The Getz uses standard two filament brake globes (1/4 turn to install).

May 12, 2014 | 2008 Hyundai Getz 1.6

1 Answer

How to replace rear brake light hyundai getz 2004


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

May 15, 2011 | Hyundai Motor 2004 Accent

1 Answer

How do I replace rear passenger side brake light on a 2007 Hyundai Sonata


There is an 'access panel' in the trunk liner right behind the tail lamp assy. Loosen wingnut to release cover. Now you have access to the bulb sockets. Be sure you replace the bulb with the same type (dual filament).. otherwise you could cause a short circuit between the 'parking lamp' and the 'brake lamp' circuits.

Sep 06, 2009 | 2006 Hyundai Sonata

1 Answer

Hyundai sonata brake lights


you will probably have to replace the bulb

Jul 07, 2009 | 2007 Hyundai Sonata Limited Sedan

1 Answer

High Level Brake bulb replacement


If memory serves, there are two screws holding this light assy to the rear package deck. They are covered (LH and RH side of this assy). remove the covers and using a phillips screwdriver, remove the screws and lift the assy up and away from the rear glass. you now have access to the bulb and socket.

May 18, 2009 | Hyundai Motor 2004 Accent

2 Answers

How to change hyundai getz brake light in light cluster?


On the Getz remove 2 screws on the outside then gently prise the cluster off from the dowels as above.

Apr 24, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Brake Light


hi from uk to change the brake light bulb/s on the getz is easy just open rear hatch then you will see 3x pozi drive screws alongside each lamp assy that screw /secure the lamp to body at the lower endof drain channel? remove screws and lift away lamp from body each bulb is accessable then now would be a good opportunity to clean the area at rear of lamp ? then reassemble is reverse as above my wife has one of these cars and has been absalutely trouble free for past 5yrs but it does get lots of tlc/servicing by myself hope the instructions are ok to follow?

Nov 23, 2008 | Hyundai Motor 2003 Elantra

Not finding what you are looking for?
2007 Hyundai Getz 1.3 Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...