Question about 2000 Toyota Avalon

1 Answer

2000 avalon front caliper not releasing. new caliper not helping

Drivers side caliper is not releasing. replaced front calipers, inspected hoses, bled brakes. still having the same problem. if you loosen connection just above the hose, the caliper releases.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 299 Answers

Replace the hose, hose is damaged internally working like check valve.

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 2005 Chevy Equinox LS and the drivers side front brakes keep locking up. Can I get some help with this problem. None of the lights come on when this happens.


Most likely the brake hose to the caliper is bad. They deteriorate from the inside and clog up, not releasing the fluid. A way to check is raise that tire pump up the brakes, release the hose at the caliper, if the caliper releases, the hose is bad, if it doesn't the caliper is bad or you have no brake pads left and the piston can/is cocked a bit.

Dec 27, 2015 | Cars & Trucks

3 Answers

2004 Dodge the longer you drive the tighter and hotter the brakes get.


all dodge caravans from 2002 through 2011 have known problems with sticking calipers. if you google caravan brake problems you will see all the complaints. there are TBI's and recalls on them. I have a 2005 dodge caravan in my garage with all 4 calipers locked up. It is a good idea to replace the brake pads with the best ones and new rotors to

Dec 13, 2012 | 2004 Dodge Caravan

2 Answers

Ford Taurus caliper sticking


If the caliper is ok, and the pads do not release, I would try the flex hose next.

Sep 01, 2012 | 2000 Ford Taurus

2 Answers

2000 Ford Taurus Wagon. Driver side rear caliper is not releasing fully. All pads and calipers were replaced at the same time. Notice diver side caliper sticking replaced and still sticks. Replaced brake...


I remember that each caliper is pushed back by "Rollout" after the brakes are pressed. If the caliper is harder to move it my not push back. May have to change O-ring seals on caliper.

Hope this helps.

good Luck

This help is free...Please make time to rate me

Yhanks

Jun 29, 2011 | 2000 Ford Taurus

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

Front breaks are smoking


caliper is sticking or pads are sticking ,proportioning valve with vehicle jacked up and supported and wheel removed inspect pads and rotor for damage excessive wear if good- turn hub/rotor by hand have someone assist u by stepping on brake observe brake caliper stop then release brake piston should release slightly from pad try turn hub again w/out touching brake if stuck in place replace and caliper released replace pads if caliper still clamped remove caliper and inspect for leak or damage compress caliper and try brake again if does if sticks again replace caliper

Oct 13, 2009 | 1988 Dodge Ram 50

1 Answer

96 Tahoe front right side brakes will noe release


Your brake hose is probably resricted slightly colaspsed on the inside replace the brake hose (wouldn't be a bad idea to replace both frt hoses) and did you lube your caliper slides pins

Oct 09, 2009 | GMC Sierra 2500HD Cars & Trucks

1 Answer

2000 chevy 1500 silverado- rear brakes overheating


Have someone push & release pedal while at wheel with problem. See if it takes a while or slow to release. If yes, have wrench ready on bleeder screw, and try again, if it sticks/holds, crack bleeder screw, if it releases, I'd replace hose.

Jan 18, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

Front disc brakes


Probably a restriction in the brake line from the master cylinder to the wheel.

Most of the time brake hoses do this (collapsed hose or hose inner liner) but the restriction could be anywhere from the point your front brake pressure divides to both wheels to the caliper of the wheel. The problem is not the caliper itself because the bleeder is able to relieve the pressure.

Aug 26, 2008 | 1993 Chevrolet K1500

Not finding what you are looking for?
2000 Toyota Avalon Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...