Question about 2009 Cadillac STS

1 Answer

Adjust switch linkage - 2009 Cadillac STS

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cadillac Master
  • 354 Answers

What is switch linkage?

Posted on Apr 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windshield wipers park wrong.


Look at the linkage if you have already located it and have someone switch on the linkage while you watch it with a flashlight. NO FINGERS You should see a nut and bolt that is on a linkage that will allow adjustment of the "at rest position". After seeing the linkage operate it should be pretty obvious which way to make the adjustment. To adjust, loosen the nut, slide the linkage and retighten. Test by operating the system. I believe I also found that you want to lift the wipers off the windshield so when you move the linkage you are trying to "drag" the wipers over the windshield.

Oct 26, 2016 | Cars & Trucks

2 Answers

How do I replace or adjust the neutral safety switch.


Before you adjust switches, get the car on a lift and be sure the shift linkage is tight. If the linkage is worn, the car may not be fully in park even though the lever and indicator look like the car is in park.

The switch is on the transmission. You should be able to see it when the car is on the lift.

Mar 31, 2015 | 2002 Mercury Grand Marquis

2 Answers

The ignition switch on my 94 Ford Crown Victoria turns freely without stopping at the positions. it starts but will not turn off. What is the problem?


you may not have the rod in the correct position so it pulls and pushes. the key has to push to start and pull the rod back to turn it off. you may have to reinstall the key lock cylinder with the rod in the right place.

Oct 30, 2014 | 1994 Ford Crown Victoria

1 Answer

Have to tilt steering wheel to start


The electric part of the ignition switch for my '86 is under the dash at the base of the steering column, and it's actuated by a rod connecting it to the key lock. Sounds like either the rod's worn so it to longer engages the electric switch in all tilt positions, or it's a neutral switch problem. Rod wear is a high-mileage issue, but adjusting the switch (loosening bolts, sliding it microscopically back and retightening bolts, should improve it. If it's a neutral switch problem (automatic transmissions only) then the truck should start with tranny in neutral gear, regardless of tilt position. Problems there are adjusted out at the linkage adjustment under the hood at the firewall, where the linkage emerges. Good luck!

Apr 03, 2014 | Ford F-250 Cars & Trucks

1 Answer

My 2001 Jeep Grand Cherokee wont start sometimes, but if I put it in neutral then try to start it..It starts .. What is the problem with my baby.......


Test/Service/Replace

The circuit on newer cars with automatic transmissions has a neutral safety, or neutral start switch installed between the ignition switch and the starter. The ignition switch cannot operate the starter motor unless the transmission is in park or neutral.
Late model vehicles with manual transmissions have a starter/clutch interlock switch that requires the clutch to be depressed to the floor.
Neutral Safety Switch
Normal operations of a neutral safety switch provides a quick check for the adjustment of the gear selector linkage.
  • To do this, move the selector slowly until it clicks into the PARK position.
  • Turn the ignition key to the START position.
  • If the starter operates, the PARK position is correct.
  • After checking the PARK position, move the lever slowly toward the NEUTRAL position until the lever drops at the end of the NEUTRAL stop in the selector gate.
  • If the starter also operates at this point, the gearshift linkage is properly adjusted.
  • This quick test also tests the adjustment of the neutral safety switch.
  • If the engine does not start in either or both of these positions, the neutral safety switch or the gear selector linkage needs adjustment or repair.

CAUTION
Since you must work under the vehicle to adjust most shift linkages make sure you properly raise and support the vehicle before working under it. Also, wear safety glasses or goggles while working under the vehicle.
A voltmeter can be used to check the switch for voltage when the ignition key is turned to the START position with the shift lever in PARK or NEUTRAL. If there is no voltage, the switch should be adjusted or replaced.

Jan 26, 2013 | 2002 Jeep Grand Cherokee

2 Answers

I have a 2003 dodge neon SE 2.0 liter L4 SFI SOHC 16V, 4 dr sedan. my problem is that the car will not go into gear or move at all. it still starts and runs great it just wont catch gears and move. Could...


if it was the neutral safety switch it more than likely wouldn`t start at all or start when without pushing on the clutch.it sounds more like the linkage could be damaged(think these are cable) or its out of adjustment and needs adjusting.does it feel like its going into gear(like it does when working) but not engaging if so it could be a problem with the transmission.first have the linkage checked out.

Aug 12, 2011 | 2003 Dodge Neon

1 Answer

My van will not start on occassion. all the electricals come on. Lights, radio, etc comes on. After I push up on the gear shift, then it starts


Hi!!
You may need to adjust the shifter linkage in relation with the neutral safety switch, if the switch is not aligned in the Park position, it won't send the signal to the starter solenoid to engage.
The adjusting is made at the Neutral Safety Switch - shifter linkage connector on top of the right side of the transmission.
Good Luck!! Don't forget to rate this post!!

Aug 24, 2010 | 2002 Dodge Caravan

1 Answer

Hi i have a 1998 ford escort zetec i have power all over the car but not to the starter or at least it doesnt turn when i turn it on


Your most likely problem is your neutral safety switch. This can be a bad switch or worn linkage. You can jumper the starter from the hot cable to the starting lug if the starter turns then that pretty much comfirms it's the nuetral safety switch.
If your problem with the nuetral safety switch is caused by the linkage you may be able to adjust the linkage. If there is an adjustment for your car it should be on the steering column under the hood or at the linkage pivit point on the frame below the steering column.

Aug 19, 2010 | 1998 Ford Escort

1 Answer

Car wont start


YOU SHOULD BE ABLE TO PUT INTO NETUAL,AND IT START.. YOUR NETUAL SWITCH IS CAUSEING IT NOT TO START.. TRY THAT IF IT STARTS, THEN YOU NEED TO ADJUST THE LINKAGE ALITTLE MORE..HOPE THAT HELPS YOU MAN..KEITH..

Mar 12, 2009 | 1994 Oldsmobile Ninety Eight

Not finding what you are looking for?
2009 Cadillac STS Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...