Question about 2003 Land Rover Freelander

1 Answer

Clutch replcing clutch

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Land Rover Expert
  • 162 Answers

The new clutch assembly will be available from any Land Rover shop but be sure to quote the Chassis number. Replacing the unit is straightforward but not a job for anyone without a hoist and some basic knowledge of these assemblies, also a spline alignment tool. If you must do it yourself, get a copy of the workshop manual and follow the instructions carefully. Honestly, by the time you mess around with it, it will be cheaper to go to a Land Rover specialist (not a dealer) and get it done professionally

Posted on Jun 17, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car won t move in any gear


Did you also replace the pressure plate? Pilot bearing? If you replaced the clutch...and the car moved, and then stopped moving again...your issue is likely right there, bad pressure plate, flywheel may need resurfaced or replaced ETC. I am curious to know what the old clutch disc looked like when you took it out. Was it glazed or worn? I would pull the tranny again, and look at the new disc to see if it is glazed looking from slipping...and note if it is both sides, or one side, and which side...plate side or flywheel side. If you didn't replace the pressure plate/pilot bearing with the clutch disc...I would do that.

Mar 21, 2014 | Honda Cars & Trucks

1 Answer

I have a 1999 dodge ram 1500 when you push the clutch in all the way there is a grinding noise and tough to engage into gear and there is a high pitched squeeling noise that comes and goes as the pedal...


you need to replce the cluch and preasure plate. the clutch is gone, its hard to shift because there is nothing left to pushout on the plate and the squeeling is from the same problem, the clutch works like brakes, when the pads are gone and you step on brake you get asqeeling sound from it being metal to metal the same thing is happening with your clutch

Mar 26, 2012 | 1998 Dodge Ram 1500 4WD

2 Answers

My 1992 Honda Accord cluth is starting to slip,opon acceleration.Is there any way to tighten the clutch,or prolong replaceing the clutch right now.


the only thing that you can do is just be easy on it and avoid fast accelaration ..the less you allow it to slip the longer you can prolong it ..so just baby it for now

Feb 21, 2011 | 1992 Honda Accord

2 Answers

How do I know when to replace the clutch on my 1999 Mazda Protege ES. Currently, it works, but I have to press the pedal all the way to the floor, with some force, to start the car. No check engine has...


whilst it works leave well alone ,when its slipping thats when you will need to replace the clutch,check the inhibitor switch on the clutch pedal though

Apr 16, 2010 | 1999 Mazda Protege

2 Answers

I have a 302,ford motor,it won't start up I turm the key and all I get is a click,I replced the solinoid ,& I still have the same problem , what can it be?


Battery and battery cables. battery must be fully charged and in good condition ,cables must be clean and tight off of battery posts and starter terminals.

Apr 02, 2010 | 1987 Ford F 150

1 Answer

Mitsubishi colt glx on a P plate is very juddery at low revs or changing gear. I've replce plugs, leads distributor and rotar arm, can you help


Have you checked if the clutch is alright or if it's an auto maybe it needs the auto transmission fluid changed and the filter cleaned.

Sep 12, 2009 | Mitsubishi Colt Cars & Trucks

2 Answers

Clutch bites high up on pedal movement


check clutch master cylinder rod adjustment and pedal height should be just higher than brake pedal. could try and bleed system also.
most hydraulic clutch systems have high take up points, adjust master cylinder rod, check for free play at top after adjusting if all that is O.K. then clutch plate may be nearly worn out but not slipping at this stage.

Jul 29, 2009 | 1997 Ford Escort

1 Answer

A/C FUSE POPS


check blower motor/ if bad replce motor and blower resister together, check ac fans and colling fan relays,ac clutch could be shorting out also hope this helped

Jun 30, 2009 | 2000 Volkswagen Golf

1 Answer

Replce a/c clutch


this is a job that requires special tools,better off replacing the compresor, at least you will get a warranty. then have it recharged by a certified A/C technician, oil will have to be added,the system MUST be evacuated and recharged with the correct amount of freon, if you need more help get back to me, please rate my fix as i strive to be the best

May 19, 2009 | 2003 Nissan Frontier Crew Cab

Not finding what you are looking for?
2003 Land Rover Freelander Logo

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...