Question about 2010 Porsche Panamera 4S

Open Question

How to install door lock actuator - 2010 Porsche Panamera 4S

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the fuses for the power dock locks on a 2006 montecarlo06ss


DR/LCK fuse 25 amp . located in the I/P block
Fuse Block - I/P
In the right front kick panel

Power Door Locks System Components
The power lock system consists of the following components:
• Body control module (BCM)
• Driver door lock cylinder switch
• Front passenger door lock cylinder switch
• Driver door lock switch
• Front passenger door lock switch
• Door lock actuators in each of the doors
• DR LK Fuse 20-amp
Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
• A door lock switch lock or unlock actuation
• A door lock cylinder switch unlock actuation
• A keyless entry transmitter actuation
• An automatic door lock actuation (Personalization function)
• An automatic door unlock actuation (Personalization function)
Door Lock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the lock position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the lock position.
Driver Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the left front (LF) door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked separate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed).

Mar 23, 2017 | 2006 Chevrolet Monte Carlo

1 Answer

Fuel door won't open on a 2008 g8 pontiac


Fuel Fill Door Description and Operation
The fuel door latch actuator shares the circuit with the driver door latch assembly. The body control module (BCM), upon receipt of a lock switch lock or unlock signal, will switch the appropriate door lock actuator, as well as a fuel filler door release actuator control circuits to battery positive voltage. The opposing side of the door lock and fuel filler door release actuators is connected to ground by the I/P fuse block through the other door lock actuator control circuit and the doors, along with the fuel filler door release, will lock or unlock as commanded.
Circuit/System Testing
  1. Ignition OFF, disconnect the harness connector at the fuel door release actuator.
  2. Test for less than 1 ohm between the control circuit terminal 1 and ground.
  3. ?‡'
    If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance.

  4. Test for less than 1 ohm between the control circuit terminal 2 and ground.
  5. ?‡'
    If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance.

  6. Connect a test lamp between the control circuit terminal 1 and control circuit terminal 2.
  7. Ignition ON, command the doors to LOCK and UNLOCK by using the door lock switch. The test lamp should illuminate while commanding the LOCK and UNLOCK states.
  8. ?‡'
    If the test lamp remains OFF during either command, test either control circuit for a short to ground.

  9. If all circuits test normal, test or replace the fuel door release actuator.
Component Testing
  1. Ignition OFF, disconnect the harness connector at the fuel door release actuator
  2. Install a 15A fused jumper wire between the control terminal 1 and 12V. Momentarily install a jumper wire between the control terminal 2 and ground. The fuel door release actuator should perform the LOCK/UNLOCK function.
  3. ?‡'
    If the function does not perform as specified, replace the fuel door release actuator.

  4. Reverse the jumper wires. The fuel door release actuator should perform the UNLOCK/LOCK function.
?‡'
If the function does not perform as specified, replace the fuel door release actuator.


Remove the rear compartment side trim (right) panel. Refer to
Rear Compartment Side Trim Panel Replacement .

Apr 06, 2016 | Pontiac Cars & Trucks

1 Answer

Drivers door will not unlock


Richard, probably a faulty or seized lock actuator.
Check the attached links how to replace actuator.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Replace Honda Civic Si Door Lock Actuator

Ford Focus Power Door Lock Motor Change

Mercedes Class W203 Door Lock Actuator Repair

. How To Install Replace Front Door Lock Actuator Dodge Durango 04 09 1AAuto...



Mar 08, 2016 | Cars & Trucks

1 Answer

How to remove the in door of a 1990 bmw 325i? And also the drivers door will not lock when i turn the key the other doors lock but the drivers door doesnt how should i go about fixing that?


Sounds like you need to replace the power door lock actuator for the driver's door.


E30 Models
  1. Remove the door panel and the water shield.
  2. Disconnect the wiring from the actuator. Remove the screws and pull the actuator off the linkage.
  3. When installing, move the actuator and linkage to the locked position.
  4. Connect the linkage to the actuator and loosely install with the screws.
  5. Compress the actuator drive to take out any play in the linkage and tighten the screws.
  6. Test the locks and install the door panel.

E36 Models
  1. Remove the door panel and water shield.
  2. On the front doors, remove the guide rail nut and pull the guide rail down. Disconnect the wiring and the linkage from the actuator.
  3. On the rear doors, remove the window and the access panel. Disconnect the wiring and the linkage from the actuator.
  4. Remove the 3 bolts holding the latch and actuator to the door structure.
  5. Install in reverse order using threadlocker on the bolts.

Mar 16, 2011 | 2003 BMW 325

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

Door lock not working on the drivers side. 1999 Ford Explorer. Need wiring diagram and how to remove the parts.


Visual Inspection Chart Mechanical Electrical
  • Binding latches
  • Door lock cylinder
  • Misaligned door
  • Lock actuator
  • Fuse
  • Relays
  • Switch
  • Wiring harness
  • Loose or corroded connections
Symptom Chart Condition Possible Sources Action
  • The door lock is inoperative
  • Circuitry.
  • Power door lock actuator (218A42).
  • GO to Pinpoint Test A .
PINPOINT TEST A: THE DOOR LOCK IS INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS A1 CHECK THE OPERATION OF THE SUSPECT DOOR LOCK sxn~us~en~file=box1.gif~gen~ref.gifCheck for binding or stuck conditions by manually operating the inoperative door lock.
  • Is the lock stuck or binding?
sxn~us~en~file=arrow.gif~gen~ref.gifYes REPAIR or REPLACE the binding components. TEST the system for normal operation.
sxn~us~en~file=arrow.gif~gen~ref.gifNo GO to A2 . A2 CHECK THE POWER DOOR LOCK ACTUATOR FOR LOCK OPERATION — CIRCUIT 117 (PK/BK) sxn~us~en~file=box1.gif~gen~ref.gif
sxn~us~en~file=ic0004.gif~gen~ref.gif Inoperative Power Door Lock Actuator
sxn~us~en~file=box2.gif~gen~ref.gif
sxn~us~en~file=gn0085a.gif~gen~ref.gif sxn~us~en~file=box2.gif~gen~ref.gifMeasure the voltage at the inoperative power door lock actuator connector Pin 1, Circuit 117 (PK/BK), and ground while operating the door lock switch to the LOCK position.
  • Is the voltage greater than 10 volts?
sxn~us~en~file=arrow.gif~gen~ref.gifYes GO to A3 .
sxn~us~en~file=arrow.gif~gen~ref.gifNo REPAIR Circuit 117 (PK/BK). TEST the system for normal operation. A3 CHECK THE POWER DOOR LOCK ACTUATOR FOR UNLOCK OPERATION — CIRCUIT 118 (PK/O)/163 (R/O) sxn~us~en~file=box1.gif~gen~ref.gif
sxn~us~en~file=gn0086a.gif~gen~ref.gif sxn~us~en~file=box1.gif~gen~ref.gifMeasure the voltage at the inoperative power door lock actuator connector Pin 2, Circuit 118 (PK/O) or 163 R/O, and ground while operating the door lock switch to the UNLOCK position.
  • Is the voltage greater than 10 volts?
sxn~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new power door lock actuator. TEST the system for normal operation.
sxn~us~en~file=arrow.gif~gen~ref.gifNo REPAIR Circuit 118 (PK/O) and/or 163 (R/O). TEST the system for normal operation.

Mar 10, 2010 | 1999 Ford Explorer

1 Answer

How do I replace the door lock actuator on a 1999 Mercury Villager w/o damaging the connecting rods and door track?


SECTION 501-14A: Handles, Locks, Latches and Mechanisms 1999 Villager Workshop Manual REMOVAL AND INSTALLATION Actuator —Power Door Lock, Front Removal
  1. Remove the front door latch. For additional information, refer to Latch—Front Door .
  1. Remove the power door lock actuator from the front door latch.
    1. Release the locking tabs.
    1. Remove the power door lock actuator from the front door latch.
583b623.gif
go here too

http://groups.yahoo.com/group/villagerquest/

Sep 26, 2009 | 1999 Mercury Villager

1 Answer

Actuator removal


please rate as solved if this is what you need. You will need to borrow a heavy duty riveter from autozone or wherever you buy the lock cylinder from.


Removal
  1. NOTE: The rear door window glass must be completely raised.
    Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
Trim Panel —Rear Door, Expedition Removal
  1. Remove the power window switchplate (14524).
  1. Disconnect the electrical connector.
  1. Remove the rear door handle trim cover.
  1. Remove the rear inside door handle.
    • Remove the door handle bolt.
  1. Remove the rear door trim panel screws at bottom of panel.
  1. s2j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the rear door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the rear door trim panel (27406).
  1. Remove the rear door watershield.
  1. Disconnect the power door lock actuator electrical connector.
  1. Drill out the power door lock actuator rivet.
9ac2386.gif
  1. Remove and discard the screws.
  1. Remove the power door lock actuator.
    • Disconnect the power door lock actuator rod.
Installation
  1. NOTE: Use new screws when installing the rear door latch.
    To install, reverse the removal procedure.
    • Use Heavy Duty Riveter to install the new rivet.

Jun 14, 2009 | 2002 Ford Expedition

2 Answers

Broken exterior door handle,passenger sider ,sliding


Got this idea from mpvclub.com: Get some stainless or aluminum sheet metal screws, drill pilot hole into the handle and into the receiving part behind, then screw in the screw. Do on both sides of handle (get appropriate length screw.) When done, get some putty or hardener to fill in the screw slot, let dry, then sand smooth, then paint with body color. Result is great and inexpensive.

Jan 26, 2009 | 2004 Mazda MPV

2 Answers

Rear Door will not Lock


Happened to me. Remove the door trim, WD40 the latching system and work it back and forth, you will be able to see were it gets hung up.

Nov 28, 2008 | 2002 Ford Excursion

Not finding what you are looking for?
2010 Porsche Panamera 4S Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...