Question about 1990 Nissan Sentra

1 Answer

Cant find where pcv valve is

Need to replace pcv cant locate it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 118 Answers

Its going to be somewhere between the hose coming off the valve cover and then to the throttle body.

Posted on Jun 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
pal03246
  • 726 Answers

SOURCE: pcv valve

pcv valve is build into the valve cover. need to replace valve cover assembly to replace pcv valve.

Posted on Aug 10, 2008

jschoon77
  • 55 Answers

SOURCE: pathfinder 2003 pcv

The PCV valve is located in the valve cover on the passenger side of the vehicle. The valve is closer to the firewall than it is to the front of the engine. It has a hose attached to it and threads into the valve cover.

Nissan Scope Technician- 10+ years experience is Nissan dealership

Posted on Nov 03, 2008

  • 1 Answer

SOURCE: 1996 nissan pcv valve location

I am used to the PCV valve being in the valve cover so I ran into the same problem myself on my 96 hardbody it is located down near the oil filter you will have to go in through the passenger front wheel well take off the splash guard and you may have to make a little room by disconnecting an electrical bracket and I believe it is a 19mm wrench.Hope this helps

Posted on Feb 22, 2009

michigan man
  • 3533 Answers

SOURCE: cant find pcv valve

for the most part it is on the valve cover try this website to see if they have your car listed its www.autozone.com and another one to checkout is www.alldatadiy.com and ihope this help you out Michigan Man.

Posted on May 24, 2009

  • 1 Answer

SOURCE: nissan pickup 1994

the pcv valve is behind the alternator between the alternator and oil filter. when you remove the oil filter you can see the pcv in the intake manifold. best way to get to it is through the pass side fender under the rubber mud flap thats between the wheel and engine.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE PCV VALVE LOCATED,I'VE SEARCHED AND STILL CANT FIND IT


PCV Valve is located in front of the engine on valve cover gasket under the rubber hose that goes from valve cover to intake manifold

Oct 08, 2013 | 1998 Ford Windstar

1 Answer

Location of pcv valve on 2008 ford taurus 3.5


On 3.5L engines, the PCV Valve is located on the rear valve cover (see pictures bellow). Please note: the PCV valve must be replaced if it's removed. Access to the valve is easier if you remove the upper intake manifold. However, this is not absolutely necessary and if you are already a little mechanically inclined you can do it the way you would replaced any other PCV valve.

    -A 19mm open wrench will make your life a lot easier if the PCV valve is a bit tight. It is in an awkward spot to apply pressure.

    -Disconnect the electrical connector from the valve. There is a small pin or locking device on the wire that you will have to slightly depress for the connector to release.

    -Disconnect the hose from the valve and turn the hose clockwise so that you have a bit of room to work with.

    -Turn the PCV valve counterclockwise and remove from the valve cover. Pay close attention to the position of the valve at the point when it is to be removed. The new PCV valve will go in at that same position. Why is this important? It is possible to install the PCV valve facing in the opposite direction. Once the PCV valve in and locked it in place, it damages the locking mechanism. Therefore, if you remove it you will have to throw it away and purchase a new one.

    -You just saved $130 - $150 to have the PCV replaced at the dealership...

location-pcv-valve-2008-ford-taurus-3-5-cgnwdhiy0mxwbb3xg5zhzgxj-5-0.jpg

Apr 07, 2013 | 2008 Ford Taurus SEL

2 Answers

Location of pcv valve on 03 ford focus


http://www.focushacks.com/images/pcv.jpg
Here's a picture to locate it..
So, when looking at the engine from above, on the right of the exhaust.

Procedure to replace it
1) Lift and support the front end of your car, or drive up on ramps
2) Get under the front of your car. The PCV Valve is located behind the exhaust manifold, a few inches below the valve cover.
3) Push up on the PCV valve to pop it out of the tube, or pull. You can get it out of the rubber tube with some effort.
4) Remove the rubber elbow from the top of the PCV valve. This can be re-used if it's not squishy. It can also be replaced cheaply.
5) Put the elbow on the new PCV Valve
6) Re-attach the elbow to the PCV tube
7) Push the new PCV valve back down into the large rubber tube

Sep 25, 2009 | 2003 Ford Focus

1 Answer

Looking for locatio of PCV valve on 2001 Accord EX 3.0?


it should be located in the rear valve couver pushed into a rubber gromet with a hose running from it to the intake tube going to air box if not there then in the front valve couver same deal with a gromet and a hose running to the intake tube going to the air box. thats were 90 percent of ur pcv valves are located on most car trucks and suv's. im not real fimilyer with the 3.0 honda moter but i hope this helps

Aug 01, 2009 | 1992 Honda Accord

1 Answer

Pcv valve location on a 89 camry


There is not a PCV valve on the 4cyl. 6 cyl. is located under hood, center, upper engine area, mounted in rear valve cover Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Jun 05, 2009 | 1989 Toyota Camry

1 Answer

Need location


The PCV valve for a 5.0L is located below the upper intake manifold in the rear. It is locate in the lower intake manifold in the rear right below the upper intake manifold. It is really hard to see but if you get a mirror you can probably see it.

Apr 12, 2009 | 1996 Ford Explorer

2 Answers

Location of a pcv valve on a 2005 honda accord


The general location mentioned is correct. However, unlike most PCV valves there is no hose connection to the valve. There is a single bolt that attachs the PCV valve to the valve cover. Loosen the bolt, then remove the PCV valve from the valve cover. It is inserted inside the valve cover. Very different from most PCV valves as far as attachment method to the valve cover.

Apr 08, 2009 | 2005 Honda Accord

1 Answer

86 buick regal pcv hose is loose


3/8 fuel line is heavy enough to use,and the pcv valve is located in the valve cover.

Feb 17, 2009 | 1986 Buick Regal

1 Answer

Pcv valve


It may be that the rubber grommet that the PCV valve plugs in to is aged and brittle, preventing the collar on the PCV valve from coming through. You may need to remove both the valve and the grommet and purchase a replacement grommet that is more pliable and allows the valve to be mounted more easily.

Sep 28, 2017 | 2002 Dodge Dakota Club Cab

Not finding what you are looking for?
1990 Nissan Sentra Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...