Question about 2003 Chevrolet Suburban 1500

1 Answer

On a 1989chevy where is thedimmerswitch

Where is the dimmer switch

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Chevrolet Master
  • 808 Answers

The dimmer switch is mounted on the column below the mounting brace for the column more on top of column on left side 2 screws hold it on.

Posted on Apr 17, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Problem battery goes dead after sitting. Did some testing that led me to lights , possibly dimmer or multi-function switch maybe ignition switch.


a dimmer switch is just a variable resistor and that only passes current at various ratings ( more resistance the lower the light
similarly switches only make and break a circuit so your problem will be after a switch possibly a faulty relay or light control module
some dimmer switches have incorporated an "OFF" section where the light gets progressively dimmer until there is a definite click for off
If your switch has that option then at full resistance but not "off" position then there will be a current flow that will be less that what is required to show light but enough to drain a battery
some vehicles that used this option were older GM or Ford products where the light switch incorporated a dimmer switch as well
the pull to first position put on the dash lights and twisting the knob gave various degrees of brightness in the dash
a further pull turned on the head lights

Jun 13, 2016 | 1990 Dodge Dakota

1 Answer

Headlights wont come on but all other lights do


Dimmer switch is on the floor, right? remove dimmer switch and replace with new one. Probably all rusted and corroded inside, you may have blow the brake switch when you hit the dimmer, also check the wiring to both the dimmer and the brake switches.

Mar 04, 2014 | 1975 Cadillac Eldorado

2 Answers

Dodge ram headlights wont work unless dimmer switch pushed


Could be the headlight switch or the dimmer switch.
I would check for voltage at the dimmer switch first.

Sep 17, 2012 | Dodge Cars & Trucks

1 Answer

Dash lights do not work 2000 ford exploier


All go out at once, first check fuses,then dimmer switch for dash lights, finally headlight switch. To check dimmer switch, pull connection off back, on harness with test light and headlight switch activated, 1 of the leads should have power, if so, use ohm meter on dimmer to make sure it has reading between 0 and some value, if no value, open, dimmer is bad, if there wasn't power then check headlight switch, there should be heavier gauge wire that powers switch and 1 for output to hi/lo switch, smaller gauge wires for tail lamps, dash lights, license plate lamps, parking lights. The color wires from dimmer would correspond to the same colored wires on headlamp switch, probe that connection on headlamp switch with switch engaged and see if you have power, if not replace switch, if so, check wire from switch to dimmer.Now if the lights slowly went from bright one day, to less bright some other day, to not working, then the bulbs are bad... good luck...

May 14, 2012 | Cars & Trucks

1 Answer

How to bleed hydraulic slave/master cylinder on 1989chevy s10 pickup?


Bleeding the slave cylinder is done just like bleeding your brake system.Just be sure that you keep enough fluid in the master cylinder so that you don't have to do it all over.Also make sure you have a steady stream of fluid.as you would with your brakes.

Mar 18, 2011 | 1997 Chevrolet S-10 Pickup

1 Answer

Fuel Filter and Fuel pump, where are they located on a 1989Chevy Silverado 1500


Fuel filter is on the rail under the truck,the fuel pump is in the fuel tank.

Apr 06, 2010 | 1989 Chevrolet K1500

1 Answer

Dash lights not working


I could be the 'insturment' or 'LPS' fuse or simply the dimmer switch. It isn't uncommon to mistakenly hit the dimmer switch at turn off the dash lights. First check to see if the dimmer switch isn't turned down. Then check the fuse. If these two are good, I would suspect the dimmer switch is the issue.

Mar 06, 2010 | 2001 Chevrolet S-10

3 Answers

High beam dimmer switch on a 1989 Cadillac Seville


Could be a couple of things. One would be that the dimmer switch has over time come loose and is now out of adjustment. Or the plastic piece in the column that pushes the rod that goes to the switch has broke. Or the switch is bad.

May 19, 2009 | 1989 Cadillac Seville

1 Answer

Auto Emission Problem


EGR FOR SURE I WOULD CLEAN OR REPLACE AND CHECK OUT KNOCK SENSOR

Nov 18, 2008 | 1989 Chevrolet K1500

Not finding what you are looking for?
2003 Chevrolet Suburban 1500 Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...