Question about 2003 Mazda 6

Open Question

P0733 shifting problam

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the 99 explorer have a vacuum modulator on the tranny and where would I find the vac hoses off the tranny.


There is no vacuum modulator on your vehicle ! It's controlled by the PCM ,all electronic shift control solenoids ! What DTC'S - diagnostic trouble codes do you have ? P0171 bank 1 lean code ? doesn't mean vac system leak ! could be a vacuum leak but also could be a O2 sensor problem or an intake manifold leak, brake vacuum booster diaphragm leak . What do you mean a slight code of gear three incorrect ratio ? P0733 ? P0733 Gear 3 Incorrect ratio Sorry Jon but you really should take this to a professional !

Jun 08, 2015 | 1999 Ford Explorer

1 Answer

How to repair transmission? Transmission is a little rough shifting when accelerating. Sometimes when I put it into reverse it hesitates and then slams into gear. I get a P0733 code.


Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Apr 09, 2015 | Cars & Trucks

1 Answer

I have a 1998 dodge Grand Caravan with codes P0700,P0734 & P0733. What does this mean?


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Jan 22, 2013 | 2003 Dodge Caravan

1 Answer

How to fix problem codes 730-733 laredo 2009


There is no one fix works for all on these code. Also you have left out the letter and one number of the code I assume these are P0730 and P0733, if so read on.

P0730 CHRYSLER - Incorrect Gear RatioPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Shift solenoids harness or connectors
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0733 CHRYSLER - Gear Ratio Error In Third GearPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Jun 27, 2012 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Codes p0700,p0733,p0734 dodge caravan 1997


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Apr 03, 2012 | 2003 Ford Focus

1 Answer

CAN I AKS A QUESTION, FOR A PROBLEM CODE P0733 FORD EXPLORER 2002 XLT


P0733 indicates which gear has a gear ratio that varies from the correct gear ratio, the corresponding in-gear trouble code ranges from DTCs P0731-36.

Without taking apart the transmission and inspecting for damage, it is difficult to say what the exact problem is, but many people who get the P0733 code have fixed the problem by replacing the accumulator in the transmission.

Other possible causes include:
  • ATF level low
  • Deteriorated ATF
  • Shift solenoid B or F malfunction
  • Pressure control solenoid malfunction
  • Line pressure low
  • Low clutch slipping
  • High clutch slipping
  • Control valve malfunction
  • Oil pump malfunction
  • TCM malfunction

Feb 08, 2011 | 1997 Nissan.5 Altima

1 Answer

My tranny have error P0733 town&country 2001 after repair automatic transmission


P0733 indicates which gear has a gear ratio that varies from the correct gear ratio, the corresponding in-gear trouble code ranges from DTCs P0731-36.

Without taking apart the transmission and inspecting for damage, it is difficult to say what the exact problem is, but many people who get the P0733 code have fixed the problem by replacing the accumulator in the transmission.

Other possible causes include:
  • ATF level low
  • Deteriorated ATF
  • Shift solenoid B or F malfunction
  • Pressure control solenoid malfunction
  • Line pressure low
  • Low clutch slipping
  • High clutch slipping
  • Control valve malfunction
  • Oil pump malfunction
  • TCM malfunction

Feb 08, 2011 | 2001 Chrysler Town & Country

1 Answer

Trouble shooting d.t.c.p0733


hi this is to do with the 3rd gear sensor switch, the switch is either faulty or the gear itself ( mechanical ) has a problem, data reads : error code p0733 fault location gear 3 incorrect ratio , possible cause: wiring or TR sensor/switch or shift solenoids or transmission mechanical fault hope this helps

Apr 06, 2010 | 2004 Mazda 6

1 Answer

2001 Jeep Grand Cherokee won't shift out of first gear and the fault codes are P0733 and P0734.


P0733=Gear 3 Incorrect Ratio
P0734=Gear 4 Incorrect Ratio,
your transmission is in "limp" mode,
Have the following sensors checked on the transmission,input sensor,output sensor,and speed sensor.
The transmission is not getting a signal from one of them,So it doesn't know how fast your going so it doesn't up shift.

Jan 22, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Code p0733, p0717


P0733 Trany Ratio in gear 3. This is a trany fault code and the first thing you should check is your tps sensor using your DVOM meter. Measuring the voltages between idle and WOT (wide open throttle), there should be no interruption in the reading (or glitches). Otherwise, it can play havoc to your shifting cycles which can cause this code P0733. If there are glitches, replace the tps sensor right away and reset the code. If trany is suspected, most common fix for this points to a defective valve body. To verify, it can be done by using a scanner which has the capacity to command the trany solenoids so it can be tested at various trany operating pressures. P0717 is a improper signal from your pules generator A. Which is a the turbine speed sensor on the transmission, You have two of them, the A reads the speed of the input shaft of the transmission and the B sensor reads the output shaft of the transmission. I know with the P0717 it will put the transmission in the limp mode and will not shift past 3rd gear and if your running the transmission hard on third you may have triggered the P0733 which is the 3rd gear slipping. Check the transmission fluid and make sure you have not burnt the fluid, if the transmission fluid is burnt you may want to have a transmission repair shop replace the turbine speed sensor (Pules Generator A) and the fluid and filter. Cross the fingers and hope the transmission was not ran to hard in third causing damage to the third gear clutch packs. Good luck and keep me posted, be glad to help.

Jun 15, 2009 | 2002 Hyundai Accent

Not finding what you are looking for?
2003 Mazda 6 Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...