Question about Cars & Trucks

1 Answer

How do I install vacuum lines for a 1992 Dodge Dakota truck

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.


    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

One line at a time so you can be sure to not cross up circuits. Do not use any petroleum products to make it easier to push the hoses on. Use only silicone spray, it will dry leaving no oily residue that will attract dirt.

I hope this helps, good luck!

Posted on Apr 17, 2014

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 2984 Answers

SOURCE: I need a picture of the fuse box diagram for a

Best suggestion is to go to your local library and get the Chilton's or Haynes manual and photo copy it for like 10 cents.

Posted on Jul 13, 2009

  • 308 Answers

SOURCE: 1992 dodge dakota ignition switch

the mechanic should check the ignition switch,the wires, the fuses, the ignition assembly ,the rotor coil, the starter solenoid and the connection of the ignition switch to the battery . If there is a worn out or destroyed spare parts then repair or replace them .the wires , if there are loose wires or worn out wires reconnect them or replace them.the fuses if there are worn out or destroyed fuses then replace them also.These are the causes of electrical problem of truck .If these said spare parts are being checked or replace then the car problem can be solved. the truck won't start because of some electrical problem not being seen . to be checked.And don't forget the connection of the battery to the ignition system . if there is a wire loose then re connect if worn out then replace.

Posted on Sep 12, 2009

  • 1 Answer

SOURCE: 1992 dodge dakota 5.2L wont shift into overdrive

I have the same problem and i cant figure out the solution either one day it worked next day it didnt

Posted on Nov 22, 2009

  • 2984 Answers

SOURCE: 1989 dodge dakota v6 vacuum diagram.

try this out:

Posted on Apr 23, 2010

  • 135 Answers

SOURCE: 1992 dodge dakota pickup truck Will not shift in



Posted on Aug 08, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fuse box panel for 1992 dodge dakota

Not all fuses are installed, only those that run the systems that were installed by the factory, you will have empty fuse slots.. I know this because I had this same truck for 20 years.

Dec 06, 2016 | 1992 Dodge Dakota

1 Answer

Cant find a actuator motor that goes on the front differential

go on line internet look for transfercase shift motor for 1992 dodge dakota.

Jan 25, 2013 | 1992 Dodge Dakota

1 Answer

1992 dodege dakota 4x4 problems changing the brake lines I was wondering if I could find a diagram somewhere

You don't need a diagram to replace all the
brake lines on that vehicle

I had one for 18.5 years and did them
3 times because of rust.

Feb 08, 2011 | 1992 Dodge Dakota

1 Answer

How do I disconnect the fuel lines from the fuel rails on my 1992 5.2L Dodge Dakota?

Push the blue plastic locks in, toward the rail

There has been no old stock on them, since 2002,have to fabricate your own deal,keep what you remove

Oct 10, 2010 | 1992 Dodge Dakota

1 Answer

My 1992 dodge Dakota is skipping and wants to stop. What is wrong? I've already changed the gas.

use a hand vacuum pump to test the egr valve. if you put about 5 inches of vacuum on it you should see movement of the pintale shaft. if not, it may need cleaned or replaced. Check the vacuum port and make sure it is not blocked or plugged.

Sep 12, 2010 | 1992 Dodge Dakota

1 Answer

Replace the wheel cylinder in 1992 dodge dakota

Back off rear drum breaks you'll need berthha a biiiggg ffff hammer knock the drum off the inter spindle once that off you gellin two bolts a break line your half way there. reverse process

Dec 06, 2009 | 1992 Dodge Dakota

1 Answer

Will not engage to 4 wheel drive

check all vacuum lines closely. i had a slight very unnoticable crack in mine and it would not go in. i just broke it off and put a rubber hose in its place and it works fine

Oct 03, 2009 | 1992 Dodge Dakota

1 Answer

I have a 1992 Dodge Dakota. When the A/C is

V6 engine? If so, there is a small plastic vacuum tube that runs from the blend door actuator under the dash to a connector in the engine compartment. The tube goes thru the fire wall about 5 inches above the throttle cable (right under the heater core tubes). The tube runs about 10 inches (behind the intake manifold) to a vacuum tube that tee's off the right side of the intake.

My tube was and NAPA did not have a tube that small but had one that fit over it for a quick splice.

Jun 14, 2009 | 1992 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides