Question about 2003 Mazda 6

Open Question

P0022 mazda6s camshaft position sensor

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 mazda 6 (wagon) is shakingand lunging forward. it was lunging while in drive and shakes like it will cut off, previous codes before this: P0022/P0345/P0431


P0022 A Camshaft Position - Timing Over-Retarded (Bank 2)
P0345 Camshaft Position Sensor circuit malfunction
P0431 Warm-up Catalyst system below efficiency

A bad camshaft sensor or wiring to the the sensor would cause the other two codes. Since P0345 refers to a circuit issue, get the wiring diagram and check the circuit before assuming you have a bad sensor. If the circuit checks out, then consider replacing the sensor. After that, clear the codes and drive to see if they come back.

Sep 23, 2017 | Mazda Cars & Trucks

2 Answers

What are the probable causes of camshaft sensor DTC?


Camshaft sensors do go bad. They can go bad slowly, so you don't notice the badness until your engine stalls, but restarts, or you get a "check engine" light. They are not expensive or hard to replace.

Nov 10, 2015 | 1999 Isuzu Rodeo

1 Answer

Keep getting code p0022


Camshaft position'A' timing over-retarded bank 2 not the sensor

Apr 14, 2015 | 2006 Ford Expedition

1 Answer

How do I fit a camshaft positioner to my Peugeot 406 gtx 136 2001 year


Some camshaft sensors must be installed AND adjusted. More likely there is also a crankshaft position sensor which is more likely to have caused your problem. You need to but an inexpensive shop manual for your car from any parts store. Also double check the error code. I believe your car has variable cam timing such that a failure in that system can set the code even if the sensor is good. Is it possible your timing belt (or chain) may have failed?

Dec 09, 2014 | Peugeot Cars & Trucks

1 Answer

Ford f150 2007 engine code P0012 and P0022


They are camshaft codes. You can try replacing the camshaft sensor. Or you can take it to a service shop and let a pro take care of it for you.

Aug 19, 2014 | Cars & Trucks

2 Answers

P0022 for 2004 toyota sienna van


P0022 Toyota - Camshaft Position \'A\' Timing Over-Retarded Bank 2



























Possible causes




- Dirty Oil

- Faulty variable valve timing (VVT)

- Faulty oil control valve (OCV)

- Variable Valve Timing (VVT) harness is open or shorted

- Oil Control Valve (OCV) circuit is open or shorted

- Damaged Engine Control Module (ECM)




Tech notes



If the engine oil is clean and the VVT and OCV circuits are OK, replaced the VVT to resolve the problem.





When is the code detected?


After the ECM sends the target duty cycle signal to the OCV, the ECM monitors the OCV current to establish an actual duty cycle. The ECM determines the existence of a malfunction and sets the DTC when the actual duty cycle ratio varies from the target duty cycle ratio.


Possible symptoms


- Engine Light ON (or Service Engine Soon Warning Light)

- Lack/Loss of power

- Engine rough idle


P0022 Toyota Description


The Engine Control Module (ECM) controls the Oil Control Valve (OCV) to regulate the intake camshaft angle. As a result of the angle change, the engine timing is advance or retard. Optimizing engine timing will help the engine improve torque and fuel economy, and the exhaust emissions decrease under overall driving conditions. The Variable Valve Timing (VVT) system includes the Oil Control Valve (OCV) and VVT controller. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control.

----------






6c14c332-d1b6-45ff-a18f-572803b2f941.jpeg

Aug 14, 2014 | Cars & Trucks

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

1 Answer

Keep getting code p0018 and p0022. plus car is rough on idle. is it expensive to fix.


Hi, a P0018 definition is Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A). A P0022 definition is "A" Camshaft Position - Timing Over-Retarded (Bank 2).

More info on the P0022 code @ http://www.obd-codes.com/p0022

As for the cost to fix, I'm not sure off-hand. A qualified technician should be able to diagnose that likely within 1-2 hours of shop time.

Jan 15, 2010 | 2006 Lincoln Zephyr

1 Answer

P0022 car shakes when idleing


P0022 - Intake position timing over retarded bank # 1

Could be timing chain on your 3.0L v-6 could have jump timing or you just have a bad cam sensor.

Jan 15, 2010 | 2006 Lincoln Zephyr

2 Answers

I have diagnostic codes of 22, 23, 24 for my 1995 Saturn Sl 1


well according to your codes that i looked up for you i think its safe to assume that your timing is off. i will paste the codes so you can see for your self. i hope this is what the codes actually look like.
P0022 "A" Camshaft Position - Timing Over-Retarded (Bank 2)

P0023 "B" Camshaft Position - Actuator Circuit (Bank 2) - See Trouble Code P0020

P0024 "B" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2) - See Trouble Code P0021

P0025 "B" Camshaft Position - Timing Over-Retarded (Bank 2) - See Trouble Code P0022

Apr 29, 2009 | Saturn SL1 Cars & Trucks

Not finding what you are looking for?
2003 Mazda 6 Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...