Question about 2004 Honda Element

Open Question

How to replace fender

Trying to replace the right side fender

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda odyssey 2010 fender - how to remove driver side fender


Need to remove mirror this will allow you to remove the part behind mirror. You ?lso need to remove headlight assembly allowing the screws behind to be removed

Mar 22, 2016 | 2010 Honda Odyssey

1 Answer

How to remove a driver side fender on a 2005 dodge durango


There are 1 or 2 under the fender up by the head light. There is 1 in the door jam behind the felt cover and 2 at the bottom of the fender by the door

Nov 16, 2014 | Cars & Trucks

1 Answer

Trying to remove the battery from my 2007 soltice


Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .


Joe
Thanks for choosing Fixya!

Jan 30, 2011 | 2007 Pontiac Solstice Convertible

1 Answer

How do I take off a front fender?


you don't remove the fender,
remove the right front wheel,in the front side of the inner fender there is a panel you need to remove to gainn access to the battery

Nov 23, 2009 | 1999 Dodge Intrepid

1 Answer

Replace side marker light on lexus rx300


Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Jul 25, 2009 | 2000 Lexus RX 300

1 Answer

Replacing the Right Front Fender on a 1999 Mazda 626


Can you remove the wheel well splash shield and get access to the bolts? Body shop techs have a special tool to get into this area.

Here's a 97 Probe whcih was the same as a 626 in 1997:

Fender, Front Removal
  1. On GT models, remove the side sill extension. Refer to Section 01-08 for the removal and installation procedure.
  1. Remove the front fender bolt located in the door jamb opening.


    RH Side Shown, LH Side Similar


    b7b1239.gif

  1. Remove the three upper front fender bolts located on top of the front fender (16005) inside the engine compartment.
  1. Raise and support the vehicle.
  1. Remove the wheel (1007).
  1. Remove one push pin and five front fender splash shield bolts and remove the front fender splash shield (16102).
  1. Remove the upper front fender brace screw.
  1. Remove the inner front fender bolt.
  1. Remove the screw holding the front bumper cover (17D957) to the front fender.
  1. Remove the two lower front fender bolts.
  1. Remove the front fender.
Installation
To install, reverse the removal procedure. Tighten the front fender bolts to 7-9 Nm (61-86 lb-in).

Feb 24, 2009 | 1999 Mazda 626

3 Answers

2003 Jeep Grand Cherokee


Find relay and give it a tap, to see if that helps. Not sure on that if its along drivers fender under hood or not, but listen for click from small 1"x1" roughly relay attached somewhere in engine compartment area, firewall, fender area.

Dec 12, 2008 | 2001 Jeep Grand Cherokee

1 Answer

2002 CHEVY AVALANCHE PAINT WARRANTY


Same problem with my 02 Northface - both sides now. Had right isde fixed and it came back worse. Now that it is over 100K miles, Chevy won't help. Only perm solution is the fender replacement.

Jul 06, 2008 | 2002 Chevrolet Avalanche

Not finding what you are looking for?
2004 Honda Element Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...