Question about 2006 Honda Element

Open Question

Drive cycle not complete - 2006 Honda Element

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I complete a drive cycle for Hyundai xg350


Take a drive on the highway and that is a drive cycle.Are you having to do so many drive cycles to make engine light go out.

Apr 29, 2015 | Hyundai Cars & Trucks

1 Answer

How do I complete a drive cycle for a Hyundai xg350


A drive cycle is simply the term for bring the engine up to full temperature. Once it does that, the drive cycle is complete, average time is usually 10-15 minutes.

Apr 28, 2015 | Hyundai XG350 Cars & Trucks

1 Answer

What is the drive cycle computer rest for 2010 corolla


drive cycle, why not just forget that. I do. (mostly)
why>?
what do I do, i reset the PCM with my $10 scan tool
when dont, all monitors are now reset, ALL !

drive cycles to finish off all monitors? (a goal for say smog testing)

that is easy most clear fast. running fast.
but not EVAP, can take up to 30min but
if fuel tank is fuel, it never completes EVAP until 1/4 lower, 3/4 full and less.
EGR tests? can be easy if you drive fast, and then coast to a stop
both tests cleared. (sans complete)
monitors are (no appliclable, not ready or complete)
to do smog, all must be complete and no DTCs. (rare exceptions)

the drive cycle means number of times it takes to set a code for one test monitor or clear one.
some newer cars take 2 drives to set them.
and is important, the FSM covers this.
why not post symptoms or reasons for asking.

just curious?, then read the ASE book on OBD2 technology.

alldata.com RTM.

Oct 10, 2014 | 2010 Toyota Corolla

1 Answer

Drive cycle


Drive cycle wont complete if a stored fault code still exists. Otherwise , 2-3 days of normal driving, city/freeway, should complete drive cycle.

Dec 19, 2013 | 2004 Mazda RX-8

1 Answer

99 Taurus drive cycle without scan tool


Technical problem that needs manufacture.

Jul 14, 2017 | 1999 Ford Taurus

1 Answer

P1111 Code


The P1111 unlike the P1000- the P1111 means the ECM has completed a drive cycle with no faults stored. The P1000 means the ECM has not yet completed the drive cycle. They are basicly drive cycle readiness codes doing a system check...this is a natural code..not to worry its checking the car all over between drive cycles for any malfunctions..
sorry i missed u online but the code is nothing to worry about...

Dec 09, 2011 | 2004 Jaguar X-Type

1 Answer

P1111 code


The P1111 unlike the P1000- the P1111 means the ECM has completed a drive cycle with no faults stored. The P1000 means the ECM has not yet completed the drive cycle. They are basicly drive cycle readiness codes doing a system check...this is a natural code..not to worry its checking the car all over between drive cycles for any malfunctions..

Dec 09, 2011 | Jaguar X-Type Cars & Trucks

2 Answers

What is drive cycle miles to make ready emission test on ford f150 5.0 engine?


a drive cycle is not measured in miles driven but in the type of driving done, here is a ford drive cycle procedure to clear the not ready code.

Ford Motor Company Driving Cycle Description of OBDII Drive Cycle
The following procedure is designed to execute and complete the OBDII monitors and to clear the Ford P1000, I/M readiness code. To complete a specific monitor for repair verification, follow steps 1 through 4, then continue with the step described by the appropriate monitor found under the "OBDII Monitor Exercised" column. When the ambient air temperature is outside 4.4 to 37.8°C (40 to 100° F), or the altitude is above 2438 meters (8000 feet), the EVAP monitor will not run. If the P1000 code must be cleared in these conditions, the PCM must detect them once (twice on some applications) before the EVAP monitor can be "bypassed" and the P1000 cleared. The Evap "bypassing" procedure is described in the following drive cycle.
The OBDII Drive Cycle will be performed using a scan tool. Consult the instruction manual for each described function. NOTE: A detailed description of a Powertrain Control Module (PCM) Reset is found in this section, refer to the table of contents.
Drive Cycle Recommendations:
  1. Most OBDII monitors will complete more readily using a "steady foot" driving style during cruise or acceleration modes. Operating the throttle in a "smooth" fashion will minimize the time required for monitor completion.
  2. Fuel tank level should be between 1/2 and 3/4 fill with 3/4 fill being the most desirable.
  3. The Evaporative Monitor can only operate during the first 30 minutes of engine operation. When executing the procedure for this monitor, stay in part throttle mode and drive in a smooth fashion to minimize "fuel slosh".
WARNING
STRICT OBSERVANCE OF POSTED SPEED LIMITS AND ATTENTION TO DRIVING CONDITIONS ARE MANDATORY WHEN PROCEEDING THROUGH THE FOLLOWING DRIVE CYCLES.

For best results, follow each of the following steps as accurately as possible:

Jun 05, 2010 | 1996 Ford Explorer

1 Answer

CAN YOU TELL ME WHAT THE P1000 CODE MEANS FOR A 1999 FORD F-150 PICK UP TRUCK


P1000 means a drive cycle has not completed, it will only clear itself after driving the vehicle through certain driving conditions. If you try to clear the code, it will reappear until you repeat the drive cycle. I am not too familiar with what AE will show, but if you can access Mode 6 data or the OBD Drive Cycle(These are two options from the IDS at Ford), It may help to show what tests have either failed or not completed. Heres what must be done to clear the P1000:


Note: The IAT PID must be between 10-38°C (50-100° F) during the OBD II drive cycle to enter into all the OBD II monitors. The FLI PID must be between 15% and 85% at all times.

Drive in stop-and-go traffic with at lease 4 idle periods (30 seconds each) while observing the status of the OBD II monitor on the scan tool. If the exhaust gas recirculation (EGR), heated oxygen sensor (HO2S), evaporative emission (EVAP), secondary air (AIR) (if applicable) or catalyst efficiency monitor have not completed, drive on the highway at a constant speed over 64 km/hr (40 mph) not to exceed 104 km/hr (65 mph) for up to 15 minutes. Heavy accelerations, sudden decelerations and wide open throttles are not recommended. If the scan tool sends out a three pulse beep at any time, the OBD II drive cycle has completed.

If there is only one certain component that hasn't completed its test, there are individual driving conditions to help those tests pass or fail if something is wrong.

Jun 23, 2009 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
2006 Honda Element Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...