Question about 2008 Land Rover LR2

Open Question

Reverse sensor won't stop beeping/2005 Lincoln

When placed in reverse.

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6468 Answers

SOURCE: My reverse sensor won't stop beeping

look for a pinched wire behind the bumper also if it was painted the paint could be to thick

Posted on Sep 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Display message says "check park assist"


Could be just a fuse. Could be wiring, module, or the sensor. It has to be diagnosed.

Apr 26, 2016 | 2005 Lincoln Navigator

1 Answer

My 2005 Lincoln ls won't go into reverse


Hi,
Time to visit a transmission shop. Call the BEtter Business Bureau for referrals if you don't know anyone local.


GL
Td

Oct 01, 2012 | Cars & Trucks

1 Answer

My reverse sensor won't stop beeping


look for a pinched wire behind the bumper also if it was painted the paint could be to thick

Sep 05, 2012 | 2008 Land Rover LR2

1 Answer

I installed the parking sensors yeaterday and now they continue to beep after I put them in reverse. I did the test where you turn on the ignition but not start the car and then put the lever in reverse....


hello i would like to help but can you give me information on the sensor kit you installed. some systems to beep and some only beep when the sensors detect something. also if they work fine with out the engine running but then don't work properly when the engine is run this could be there is to muck voltage for the sensors, some sensor kits are saying they are 12v, this is correct 12 volts, but the charging system on most vehicles are 14 volts, so you may have to fit a regulator to the feed wires to the sensor. you would need a 12 volt regulator board. this will stop any power going over the 12 volts to the device.

Jun 30, 2017 | 2005 Nissan Pathfinder

1 Answer

Lincoln backup sensors beeping in reverse with no object behind


Either the sensors is defective , the relay or there is a short in the circuitry.

Mar 26, 2010 | 2003 Lincoln Town Car

1 Answer

Reverse sensors work some days but then on some days I get 3 second audio alarm when I turn on ignition,


I find the sensors only activate when you are very close to an object behind you. At about 5 inches they beep constantly. Further then five inches they beep slower and slower until they stop at about 8 inches from something behind you. If you are very close to an object lest then 2 inches they will beep constantly. Also when you start your car and put it in reverse and you hear a beep the reverse sensors are not working. The best way to test them is to turn the key to the start position but do not start it. place the lever in R get out or have someone walk in back of the car, you should hear the sensor go off. Also, there might be a situation when one or two are not working. Follow the procedure above for test but have a stethoscope mechanic type, which most auto parts stores carry. and listen to each one individually. If one is not working it will have to be replaced. The control module for this system is in the trunk next to the spare tire. Some of these cars had a leaking trunk problem in 02 if the module is wet, get a new one. If it hasn't failed it will when they get wet. Finally the sensors should be heard inside and outside the car.

Mar 05, 2010 | 2005 Jaguar X-Type

1 Answer

Jaguar XK8 2005 beeping/no reverse sensors working.


I have the same problem on my XK8 2005....did you find a solution?

Jan 29, 2010 | 2005 Jaguar XK8

1 Answer

Why has the parking sensors on my bmw stopped working


There is few options.First-reverse switch not working.How to check-switch ign. ON,select Reverse and check reverse lights at back.If not-change switch.If O.K. go to step two: Disconect reverse sensors next to a bumper and check for resistance/any one/,because all sensors are conected in serie.If there is not resistance check all sensors one by one to find a wrong one.And last one-check "beep" speaker

Dec 07, 2009 | 2005 BMW 1 Series

1 Answer

2003 Lincoln Navigator back up sensor immediately and continuously beeps when vehicle is placed in reverse, even when there is nothing anywhere near the vehicle as it is backing up. Had Ford/Lincoln...


yes it would cause the check engine light to come on.But just find the bleeper and remove it it want affect the cencer.The bleeper is separate from the censer..

Jun 03, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
2008 Land Rover LR2 Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...