Question about 1994 Toyota Pickup
Can you provide a step by step procedure for changing the CV joints on a 1994 Toyota pickup. Thanks!
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I would recommend that you replace the complete axles instead of just the boots. The boots may be busted/worn and when the get torn/busted they allow sand/dirt inside the CV joint and the bearing inside the CV joint become worn, it all depends on how long the boot has been ripped, its easier and a lot less messy to R/I new axle. For the wheel bearings they need to be pressed in by a hydraulic press. As far as the procedure goes you have to elevate the two front wheels and secure by a lift of jack stands, then take off tires and take off brakes/caliper and caliper chair along with the rotors. You have to remove center nut on axles and remove lower ball joint from knuckle assemble/ hub. Then remove bolts holding knuckle/hub to the struts. Pull knuckle from axles and the hub is out. If you don't have a press and the proper tool you can take the two hubs and the bearings to a machine shop and they will press out and pressing new bearing for you. As for the axles they both can then be pulled/pryed out of the transmission at this time and be fixed or replaced. caution look out for leaking transmission fluid when you pull axles out. The axles are only held by licking rings and can be easily pulled or pryed out. Have something ready to catch fluid. Replace axles in the reverse of taking out. use a piece of wood on the end of axle if there is need to tap it back in with a hammer, listen for a click or snap when its goes back in to transmission. Good Luck
Posted on Dec 12, 2008
SOURCE: Changing a CV joint
CV boot and CV joints are different. Boot covers the joint which protects it from debris and other harmful things. if your boots are cracked then just change them. pretty cheep to do yourself. but if you look at the joints and there is dirt on them then you have a problem. i have that same thing and its fine for me unless i turn on the 4W. then you hear a clicking noise. eventually if you keep going like that your car will stop moving. you can look to buy new cv halfshafts. for a good price go to pep boys. best deal i've found anywhere
Posted on Feb 10, 2009
No you do not need to remove the motor. You will need to remove the driveshaft from the gearbox (driver side) so you may need to drain the gearbox oil. Passenger side has an intermediate shaft and the drive shaft can be split without removing from the gearbox.
One the shaft is off remove the outer boot and nock the old CV joint off with a hammer and somthing to take the impact without damaging the joint (incase its re-useable). I used the rubber end of a screwdriver on the joint and hit the metal end of the driver with a hammer.
If the CV joint boot you have recieved is not the strechy type you will need to slide it onto the shaft prior to installing the new joint.
To install the new joint can be a chew. There is a circlip seated in a groove on the outer splines of the driveshaft. This clip is slightly larger than the groove it sits in must be "negotiated" into the groove while you slide the new cv joint over (Use a flathead screwdriver to prize the circlip in as you push the new CV joint onto the shaft.) Once you get this right the CV joint will slide down and the circlip will make an audiable click and pop out of the groove on the inside of the joint holding the join in place.
Pack the joint with the grease provided. Slide the boot over and fasten the boot in place with the metal straps and put your car back together.
Beware of new Circlips - my old one was mishapen so I used the new one provided and it was massive in comparison. It took me and a friend a good hour and a half just to get the new CV joint over the circlip - patience is a virtue :D
Incase you can get the shafts out....
Best way is to split the bottom ball joint and suspension wishbone. I'm not a massive fan of this as bottom ball joints have caused me too many issues. I split the tom ball joint and the tracking rod end to give enough movement to get the driveshafts out.
Also never pull on the driveshaft its self as this can pull apart the inner joint inside its boot which is a real faff on to get back together (trust me). Use a screwdriver or small crow bar to prize the shaft out at the gearbox end.
Posted on Feb 24, 2009
Instead of telling you. You should go to autozone.com and register for full free online repair manual with extras. I recommend it to all my customers as a mechanic myself
Posted on Sep 12, 2009
SOURCE: 1992 Toyota Corolla CV Joint
You can pick up an entire re manufactured axle assembly at your local auto parts store. In order to replace the assembly you will need to disconnect the tie rod end and the ball joint. Remove the spindle nut. Push the axle stub out of the hub. Now with a suitable container under the axle to catch spilled fluid pry the axle from the transmission housing. Install is the reverse of removal. For more detailed instructions and diagrams go to www.autozone.com vehicle repair guides.
Posted on Oct 29, 2009
Tips for a great answer:
Mar 23, 2014 | 1994 Toyota Camry
Sep 08, 2011 | Toyota Corolla Cars & Trucks
Mar 16, 2010 | 1994 Toyota Celica
Feb 14, 2010 | 2000 Toyota RAV4
Mar 25, 2009 | 1994 Toyota Camry
Jan 13, 2009 | 1994 Oldsmobile Achieva Special Edition
909 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: