Question about BMW 325

Open Question

P0465 small pressure leak - 325 BMW Cars & Trucks

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

geaeri95
  • 127 Answers

SOURCE: engine error lite P0465

Replacing the EGR valve, its actuator, or your DPFE sensor could all be at fault. I would probably start with the valve itself since it's an EGR leak code. Your gas cap was a wasted repair. The gas cap would cause a P0441 or 445 evap code, but not an EGR code.

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0442 toyota camry 2006 trac off, vsc on, chk engine on


code p 0442 refers to evaporative emissions(EVAP) system---small leak detected ===causes ---hose connections ---intake leak---EVAP canister---EVAP cannister purge valve
it also refers to mechanical fault --hose connections --EVAP pressure sensor

May 06, 2017 | Cars & Trucks

1 Answer

Engine scan codes are P0442, P0456 , can you please help me with these codes


P0442 - Evaporative Emission Control System Leak Detected (small leak)
This indicates a fuel vapor leak in the EVAP control system. It means a very small leak has been detected. In fact, the leak can be from a hole as small as 0.04" in diameter. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0442 most likely means one or more of the following has happened:
A loose or improperly affixed gas cap
A non-conforming gas cap (i.e. not factory/original brand)
A small leak/hole in a fuel vapor hose/tube
Other small leak in EVAP system
Faulty vent o-ring seal

Possible Solutions: With a P0442, the most common repair is to:
Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
Otherwise, replace the gas cap, or
Inspect the EVAP system for cuts/holes in tubes/hoses



P0456 - Evaporative Emissions System - Small leak detected
The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the fuel tank pressure (FTP) sensor. When the sensor indicates a small leak in the EVAP system, this code is set.

Potential Symptoms: There will likely be no noticeable symptoms other than the Malfunction Indicator Lamp (MIL). This is because the EVAP system is a closed system and only controls fuel tank vapors, not engine management.

Causes: Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivable cause this code as well or if the cap wasn't properly tightened. Any of the following could also be the cause:
A small leak in any of the EVAP hoses or fuel tank hoses
A small leak in the purge valve or vent valve
The EVAP Canister may be leaking

Possible Solutions: First, using a scan tool activate the vent solenoid, sealing the system. Then monitor the fuel tank pressure (FTP) sensor. If the system is sealing properly, the number will stay consistent. If is isn't, the pressure sensor will show that as well. If the system slowly leaks, use a smoke machine and watch for smoke exiting the system at any EVAP component. Any where there is smoke exiting the system, that is the faulty component. Do not pressurize the EVAP system with air pressure. Doing so can damage the purge and vent solenoids in the system.


Test it; keep us updated and remember to rate this answer.

Jun 03, 2011 | 2005 Dodge Grand Caravan

1 Answer

Po456 dodge caravan


P0456 - Evaporative Emissions System - Small leak detected
The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the fuel tank pressure (FTP) sensor. When the sensor indicates a small leak in the EVAP system, this code is set.

Potential Symptoms: There will likely be no noticeable symptoms other than the Malfunction Indicator Lamp (MIL). This is because the EVAP system is a closed system and only controls fuel tank vapors, not engine management.

Causes: Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivable cause this code as well or if the cap wasn't properly tightened. Any of the following could also be the cause:
A small leak in any of the EVAP hoses or fuel tank hoses
A small leak in the purge valve or vent valve
The EVAP Canister may be leaking

Possible Solutions:
First, using a scan tool activate the vent solenoid, sealing the system. Then monitor the fuel tank pressure (FTP) sensor. If the system is sealing properly, the number will stay consistent. If is isn't, the pressure sensor will show that as well. If the system slowly leaks, use a smoke machine and watch for smoke exiting the system at any EVAP component. Any where there is smoke exiting the system, that is the faulty component. Do not pressurize the EVAP system with air pressure. Doing so can damage the purge and vent solenoids in the system.

Hope this helps.

Jun 03, 2011 | 2002 Dodge Grand Caravan

1 Answer

PO456 trableshooting


Info found at: http://www.obd-codes.com/p0456

Maybe try cleaning, tightening, or replacing the gas cap first?


P0456 Article by Dale Toalston ASE Certified Technician

Evaporative Emissions System - Small leak detected

The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the fuel tank pressure (FTP) sensor. When the sensor indicates a small leak in the EVAP system, this code is set.

Potential Symptoms:

There will likely be no noticeable symptoms other than the Malfunction Indicator Lamp (MIL). This is because the EVAP system is a closed system and only controls fuel tank vapors, not engine management.

Causes:

Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivable cause this code as well or if the cap wasn't properly tightened. Any of the following could also be the cause:

- A small leak in any of the EVAP hoses or fuel tank hoses

- A small leak in the purge valve or vent valve

- The EVAP Canister may be leaking

Possible Solutions:

First, using a scan tool activate the vent solenoid, sealing the system. Then monitor the fuel tank pressure (FTP) sensor. If the system is sealing properly, the number will stay consistent. If is isn't, the pressure sensor will show that as well. If the system slowly leaks, use a smoke machine and watch for smoke exiting the system at any EVAP component. Any where there is smoke exiting the system, that is the faulty component. Do not pressurize the EVAP system with air pressure. Doing so can damage the purge and vent solenoids in the system.

Apr 13, 2011 | 2004 Volvo XC70

1 Answer

Evap code p0456


P0456 - Evaporative Emissions System - Small leak detected
The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the fuel tank pressure (FTP) sensor. When the sensor indicates a small leak in the EVAP system, this code is set.
Potential Symptoms

There will likely be no noticeable symptoms other than the Malfunction Indicator Lamp (MIL). This is because the EVAP system is a closed system and only controls fuel tank vapors, not engine management.

Causes: Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivable cause this code as well or if the cap wasn't properly tightened. Any of the following could also be the cause:
* A small leak in any of the EVAP hoses or fuel tank hoses
* A small leak in the purge valve or vent valve
* The EVAP Canister may be leaking

Possible Solutions: First, using a scan tool activate the vent solenoid, sealing the system. Then monitor the fuel tank pressure (FTP) sensor. If the system is sealing properly, the number will stay consistent. If is isn't, the pressure sensor will show that as well. If the system slowly leaks, use a smoke machine and watch for smoke exiting the system at any EVAP component. Any where there is smoke exiting the system, that is the faulty component. Do not pressurize the EVAP system with air pressure. Doing so can damage the purge and vent solenoids in the system.


Hope this helps.

Mar 24, 2011 | 2007 Mitsubishi Endeavor

1 Answer

I have a 2003 jeep wrangler that will not start and is displaying code P0465.....I have replaced the starter 3 times in the past 6 months...What is this error code?


p0465 = Purge flow sensor circuit malfunction. It has nothing to do with the starter, and diagnosing this code can be very challenging without the proper tools.

Sep 13, 2010 | 2003 Jeep Wrangler

1 Answer

The engine light is on in my 2001 Chrysler Concorde. Pulled the code: P0456 came up. Any ideas?


Evaporative Emissions System - Small leak detected

The Powertrain Control Module
(PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank
vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the Fuel tank pressure sensor (FTP). When the sensor indicates a small leak in the EVAP system, this code is set.

Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivable cause this code as well or if the cap wasn't properly tightened. Any of the following could also be the cause:
· A small leak in any of the EVAP hoses or fuel tank hoses
· A small leak in the purge valve or vent valve
· The EVAP Canister may be leaking

Possible Solutions
First, using a scan tool activate the vent solenoid, sealing the system. Then monitor the fuel tank pressure (FTP) sensor. If the system is sealing properly, the number will stay consistent. If is isn't, the pressure sensor will show that as well. If the system slowly leaks, use a smoke machine and watch for smoke exiting the system at any EVAP component. Any where there is smoke exiting the system, that is the faulty component. Do not pressurize the EVAP system with air pressure. Doing so can damage the purge and vent solenoids in the system.

Nov 22, 2009 | 2001 Chrysler Concorde

2 Answers

JEEP DEALERSHIP PERFORMED HEAD GASKET REPAIRS ON 2001 JEEP GRAND CHEROKEE THAT STOP COOLANT LEAK. PRIOR TO REPAIR ANTIFREEZE HAD LEAKED BUT SHOWED NO SIGNS OF LEAKAGE. AFTER REPAIR CAR RAN FINE WITH NO...


Check your water pump for signs of seepage. Do this with no pressure in the system and cap off. Sometimes in the beginning stages of failure pressurizing the system will drive the seal against the shaft and actually hide the leak. I have seen very small cracks in cylinder heads, especially between the valves that won't show up on a pressure test 'till they get worse. Check the plugs for any coloring from antifreeze.
You are going in the right direction so far, but need to go over everything sometimes a few times before a small leak is found. Keep an eye out for dried or semi-dried stains, especially around the perimeter of the head /block parting line...sometimes small leaks will only leave a slight stain, often white or antifreeze colored powder residue.
Hate to say it, but sometimes when you can't find it, just put some block sealer in there and see if it corrects the problem.I'm a professional but sometimes just doing that saves a big headache for a small problem.

Nov 19, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Engine code 456


Evaporative Emissions System - Small leak detected

Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivably cause this code as well or if the cap wasn't properly tightened.

Any of the following could also be the cause:
  • A small leak in any of the EVAP hoses or fuel tank hoses
  • A small leak in the purge valve or vent valve
  • The EVAP Canister may be leaking
Solutions...
First, using a scan tool activate the vent solenoid, sealing the system. Then monitor the fuel tank pressure (FTP) sensor. If the system is sealing properly, the number will stay consistent. If is isn't, the pressure sensor will show that as well. If the system slowly leaks, use a smoke machine and watch for smoke exiting the system at any EVAP component. Any where there is smoke exiting the system, that is the faulty component. Do not pressurize the EVAP system with air pressure. Doing so can damage the purge and vent solenoids in the system.

Oct 30, 2009 | 2002 Chrysler Town & Country

2 Answers

Engine error lite P0465


Replacing the EGR valve, its actuator, or your DPFE sensor could all be at fault. I would probably start with the valve itself since it's an EGR leak code. Your gas cap was a wasted repair. The gas cap would cause a P0441 or 445 evap code, but not an EGR code.

Oct 07, 2009 | 2000 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...