Question about Cars & Trucks

1 Answer

04 crown victoria not turning over battery gud new alternator

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 157 Answers

Connections? at the battery posts are good? power available at starter relay? car is in park or neutral? now you need to verify theres power on the start wire. the small trigger wire for start enable. if a test light or voltmeter wont show power during crank, then it may be theres a problem in the neutral safety. it has to know the trans is out of gear. newer vehicles have mlp sensors instead of neutral safety switches. its time to get a service manual and determine the pinpoint test for this vehicle

Posted on Apr 17, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

  • 102 Answers

SOURCE: how to trouble shoot starting system 98 ford crown victoria

Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

Posted on Sep 23, 2009

reisdos
  • 1297 Answers

SOURCE: fuse diagram for 2000 crown victoria

there are 5+ pages of fuses what specifically do you need


Posted on Jul 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After replacing the alternator airbag light and battery light stays both lights go off and car dies.


electrical issues since replacing alternator & battery - Mazda 6 ...

forum.mazda6club.com > Mazda6 (Atenza) > Newbie Section
Dec 24, 2010 - Exclamation Battery Light after Replacing with New Alternator ... TheBattery Light stays on after I start the vehicle. It comes up after ~2-3 secs of ...

Battery light flashing, air bag light on, after alternator pulley ...

https://forums.tdiclub.com/showthread.php?t=343786
Feb 11, 2012 - Battery light flashing, air bag light on, after alternator pulley changeTDI 101. ... Almost a week later I am driving home and the battery light flashes on, then off, .... Seat belt light stays on, no air bag light. cjharris02892, TDI 101 ...

Battery Light Due to Damaged Alternator Wire Harness ...

repairpal.com > Problems > Ford > Crown Victoria
Battery Light Due to Damaged Alternator Connector on Ford Crown Victoria ... how can i turn off the airbag light on a 1991 crown victoria made by ford ... the battery light onreplace alt and batt light still what else can it be? thaqk. it sat for two weeks when we had snow i used my truck staqrted car light comes on and stays on.

Airbag light = bad battery - Maintenance, Recalls and T


Dec 27, 2015 | Cars & Trucks

1 Answer

2000 crown victoria won't start after i got a new battery and altenator. What can the problem be?


The starter or it's solenoid

The new battery & alternator didn't
but the problem in there

Jun 09, 2011 | 2000 Ford Crown Victoria

1 Answer

1991 crown vic, new battery, alternator, power going to alternator, still won't charge battery... plz help!!!!!!


check the ground cable. the ground straps to the engine and body alos. Make sure the cables are clean and have no corrosion anyplace.

Mar 17, 2011 | 1991 Ford LTD Crown Victoria

1 Answer

04 crown vic alt no charge


Well, either you have a bad alternator or a broken wire at the alternator. Check the small red field wire which excites the alternator and the large red output wire. Also check for a loose belt. Make sure your battery is charged as trying to charge a dead battery can overload and destroy an alternator.

Dec 11, 2010 | 2004 Ford Crown Victoria

1 Answer

1997 Crown Victoria. Battery is known to have low capacity due to age. Last several months notice alternator idiot light glowing during hard acceleration. Upon startup tonight it won't charge at all,...


You need a new alternator. Install a rebuild or get a used one from a wrecker for cheaper. It won't be worth the headaches of trying to replace brushes as that might not even solve your problem.

Feb 01, 2010 | 1997 Ford Crown Victoria

1 Answer

2004 crown victoria lights dont work brake lights dont work turning light dont work


If it is an '04, the lighting control module (LCM) is most likely the culprit. The LCMs were largely no good for '03 and '04. It is located at the bottom on the instrument panel basically above your right shin. Easy to replace, but kind of pricey.

Jan 16, 2010 | 1994 Ford Crown Victoria

2 Answers

I have 1998 ford crown victoria everyday I have to jump start my car what can be wrong


I would suspect you need a new battery and yours has a dead cell. Remove the battery and have it tested at any auto parts store.

Sep 30, 2009 | 1998 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...