Question about 2007 Cadillac DTS Sedan

1 Answer

How do I replace the front turn signal bulbs - 2007 Cadillac DTS Sedan

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You have to take off the headlamp assembly, 2 bolts, easy to spot. comes out as 1 unit. lots of wire. shouldn't have to adjust anything if ytou put the washer back in the same mark it left in the frame. 1 bolt on top under the flap on either side. i bolt on the bottom by the radiator opening. hope this helps

Posted on Apr 19, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

  • 1 Answer

SOURCE: Front turn signal bulb replacement

In your manual on page 5-53 it states how to change the bulb out
for the turning signals - we had the drivers side out. Gave it to our mechanic and had it completed in about 2 hours.

Posted on Feb 23, 2009

  • 1 Answer

SOURCE: 2004 CTS Cadillac front passenger turn signal bulb is out.

Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.

Posted on Mar 14, 2010

duane_wong
  • 6826 Answers

SOURCE: How do I replace the front turn signal bulb?

that's a tough one to do. Requires unscrewing bolts underneath the car to remove the entire lense assembly. Best left to a professional or a lot of time (1 or 2 hours) to undo everything and put it back.

Posted on Jul 02, 2010

  • 1 Answer

SOURCE: Need to replace the right front turn signal bulb

I called the dealer,They wanted $85 an hour,an two hours to do it!!!!I took the front splash guard off under the front ,Just put on with plastic plugs,Then took the inner fender well off also with plastic plugs.Turned the wheel in,I didn't have to remove it.. and used a screw driver to take a cover off to get at the bulb..It took some time and it was not easy to get at.But it was warm outside when i did it,and saved afew bucks too!!Be patient and its really not that hard.I've done it twice......

Posted on Jan 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My left turn signal was flashing fast. I checked bulb in back left. Turn signal good but bulb below it was out. I changed that one but turn signal still flashing fast. all other bulbs look good. ??


If the front and rear bulbs flash fast also, replace the hazard switch or you could live with it. As they are working. If one doesn't work, check grounds. I just run a new ground, much easier than cutting open the harness to find the break.

May 31, 2015 | 2012 Nissan Rogue

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

3 Answers

Fast flashing turn signals


I would change out the turn signal bulb on the right front. A blown bulb can cause the fast flash issue. The signals staying on is not related to the bulb being blown. That is most likely a problem with the multifunction switch, the knob you use to signal.

Jul 12, 2013 | Buick Cars & Trucks

1 Answer

Grand prix front turn signals lights will not work but rears flash rapidly.


Definitely not the flasher, as long as it is flashing or blinking somewhere. Rapid flashing indicates a burned bulb, but since you already tried new bulbs in front, possibly bad bulb sockets, loose connectors, or a bad ground for the front bulbs. If you have a test light or voltmeter (multimeter), check for power at the socket when turns are on. If power then at the front, try new bulbs or trace the ground for those lights. If no power to the socket for turn signals, recheck wiring.

Apr 02, 2013 | 1995 Pontiac Grand Prix

1 Answer

How do you change a front signal bulb on a 2004 accord


Front turn signal bulb replacement

1. Remove the inner fender
2. Disconnect the 3p connector from the front turn signal/side marker light.
3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.

Apr 12, 2010 | 2004 Honda Accord

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

2 Answers

Need replace turn signal bulb


YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

Aug 24, 2009 | 1996 Chevrolet Cavalier

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

1 Answer

2000 Accord turn signal problem


either the front or the rear turn signal bulb is blown, that is why the flash frequency is high. replace the bulb and the problem will be solved. best to replace both the front and rear turn signal bulbs. good luck.

Aug 29, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2007 Cadillac DTS Sedan Logo

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...