Question about Cars & Trucks

Open Question

How do i fix a hein werner floor jack? - Cars & Trucks

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
J-Chris Ward
  • 731 Answers

SOURCE: Hi I'm looking for a service manual for a Hein

Here a site you are looking for.http://www.ohiohydraulic.com/hein-werner%20drawing%20page.htm
http://www.ohiohydraulic.com/hein-werner/WS.pdf

Posted on Feb 15, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 8287 series, when I was lifting the jacks a role pin fell out of somewhere and now the passenger side jack will not move up or down, we're was that role pin located so I can fix this


Hello Doug...

No hits on "8287" as a meaningful jack "IDENTITY".

Just a guess here... but if you want to get that jack out... you'd be wise to get a block of wood... a jack stand... and relieve the DISABLED jack... by jacking higher (installment plan).

Stuck jacks can be quite dangerous...
Get it out of there... Then (and ONLY then)

Look to the handle linkage... for your "roll-pin"...

You will be proud


3 ton Low Profile Steel Heavy Duty Floor Jack with Rapid Pump

Aug 23, 2016 | Cars & Trucks

1 Answer

Fuel filter location?


most are in the gas tank.

Easy job if you have a floor jack, 2 floor stands and wrench.
Empty the gas tank, place jack centered on the gas tank jack up the car, put the floor stands in place to hold the car steady, disconnect the wiring go to the gas tank then remove the bolts (most cars only have 2 holding the tank braces, slowly lower the floor jack with the tank on it, remove the fuel pump slowly and carefully as not to have anything fall in the tank.
https://www.youtube.com/results?search_query=remove+gas+tank

Dec 10, 2015 | Cars & Trucks

1 Answer

How can i fix a floor jack it does not go up


that depends did it leak oil out of the shaft seal ? if it did you could add more oil to resavor but that would not be safe as oil will continue to leak out seal and jack will fall down , Most auto parts stores sell hyd jack oil in a can

Sep 22, 2014 | Cars & Trucks

1 Answer

My mvp 3ton floor jack will pump p but wont hold


First you need to check and see that it is full of fluid. It could be the release valve is leaking. It is the valve you unscrew to let the jack down. You need to unscrew the whole assembly and inspect it to determine condition, fix as required.

Sep 19, 2014 | Cars & Trucks

1 Answer

I dont know how to change the drivers side transmission mount on my 99 alero what would be the best way


YOU NEED TO SUPPORT ENGINE TO REMOVE TRANSAXLE BRACE.YOU CAN USE FLOOR JACK WITH A PIECE OF WOOD ON JACK SADDLE.YOU NEED TO REMOVE WHEEL OR TIRE SPLASH SHIELD TO REMOVE THE TRANSAXLE BRACE PLACE FLOOR JACK WITH A PIECE OF WOOD IN JACK SADDLE PLACE JACK UNDER THE ENGINE OIL PAN.SLIGHTLY RAISE JACK A LITTLE JUST ENOUGH TAKE PRESSURE OFF THE TRANSAXLE TO REMOVE TRANSAXLE BRACE.DONT RAISE FLOOR JACK UP TOO MUCH UNDER THE ENGINE OIL PAN BECAUSE YOU COULD DAMAGE OIL PAN AND OIL PUMP.

Jun 25, 2011 | 1999 Oldsmobile Alero

1 Answer

How do i replace my starter for my 1992 Lincoln Town Car?


First disconnect battery. Use a floor jack to lift vehcile from passenger side. Use floor jack to help hold up car for safety. The starter will be located ton the passenger side. It is held by two bolts. There will be one wire to a 10 mm nut. remove. There will be a couple of wires in cluding one from the baterry to a big bolt remove the nut. Remove the two bolts being careful as starter may drop. You can use the floor jack to help you since the floor jack is suppporting the vehicle. Reinstall in reverse.

Nov 17, 2009 | 1992 Lincoln Town Car

1 Answer

Door sag chevy suburban


put a car floor jack under the door and jack it up loosen the screws and try to close the door, you might need shims or washers. tighten each screw top bottom each one til its down so door must be leviled on the jack then bolt it on one at a time

Jan 10, 2009 | 1999 GMC Suburban

2 Answers

1999 passats motor mounts how do i fix them


You will need to jack the car up as far as possible, then put it on jack stands and remove the floor jack, then put a thick piece of wood on the jack pad and take the weight off the Motor Mounts, this will allow you to get the bolts out and remove them, make sure you use jack stands and at least a 3,000 LB capacity floor jack. BE CAREFUL!

Nov 12, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...