Question about 2008 Honda Odyssey

Open Question

Replace 2008 honda odyssey passenger side inner tail lamp assembly

Replace passenger side inner tail lamp assembly

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dr_greg
  • 192 Answers

SOURCE: Passenger side rear power window is not opening

the rear side window vent motor is bad, u need to replaced it...common on these vans...i hope its the left rear and not the right....right is a little more difficult re installing due to the rear a/c ducts

Posted on Apr 13, 2009

Ad
  • 1986 Answers

SOURCE: I need to replace the passenger side mirror on my

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls and the mirror. Then you can access the bolts securing the mirror onto the door....

Posted on Oct 20, 2009

  • 1986 Answers

SOURCE: need to remove inner rear passenger side door

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle

Posted on Nov 05, 2009

  • 77 Answers

SOURCE: 2004 honda odyssey rear window passenger side

First check fuse #7 and #16 in the passenger side dash fuse box, however I've seen this happen allot on this body-style of Odyssey's. Here's a quick check you can perform: Operate the rear vent window switch and listen for a 'click' in the rear of the van next to the vent window. This is the relay 'clicking'. If you hear the relay 'Click' you now know that your getting power in the circuit. This means that the vent motor is faulty. This is a common failure and they usually go out in pairs, so the other side maybe on its way out too. If you don't hear the 'click' than you'll have pin test the multiplex control circuit for a fault.
-hope this helps

Posted on Feb 06, 2010

SOURCE: WHERE IS HONDA CRV TAIL LAMP FUSE

hi,
i have provided the picture showing the location of tail lamp fuse for Honda. I have marked it too for your reference. Please rate my solution as helpful.Have a nice day!7c6a615.jpg

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High brake light


You will have to remove inner garnishing...To access the upper tail light...the rest of the wiring is fed in through the of the van...you will have to follow the wires...be patient....all the wires should be on the drivers side....

Nov 24, 2013 | 2008 Honda Odyssey EX-L

1 Answer

I had the dealership address the rattling of the sliding passenger door on our 2002 Honda Odyssey. The removed the inner panel and adjusted the door striker which didn't stop the rattle. Any suggestions...


The sliding door has upper roller, lower roller, and center roller mechanisms. These rollers can become damaged and rattle in their respective tracks. The upper and lower rollers are easy to inspect, as they are at the front of the door (top and bottom) and in plain sight. But the center roller cannot be inspected until the center rail cover (an exterior narrow long panel) is removed.

To remove the center rail cover, first remove the tail light assembly on the affected side. (That procedure can be found by doing a fixya search for "2002 Honda Odyssey brake light replacement"). Now open the sliding door. Notice at the front of the rail cover there is a small bolt. Remove this bolt. Go to the back of the center rail cover and remove the two screws (only accessible when tail light assembly is removed). Then slide the center rail cover rearward to remove it. Now you will be able to inspect the center roller mechanism and door cables. Look carefully for damaged rollers which will let the door wobble in the center track and rattle.

How do these rollers get damaged? When kids climb onto the doors and "slide along". The door guide rollers and latches were not designed to carry much more weight than the door itself.

Mar 28, 2011 | 2002 Honda Odyssey

1 Answer

I need to replace the passenger side (tailgate) tail light assembly, but it won't come out after taking the 4 nuts out.


Remove 4 screws, and gently pry it off. It is held by a stick adhesive. You can place a rag over the painted body, and pry the light assembly off and it will come off. Just gently work your way pry around the entire light assembly and it will come off.

Oct 08, 2010 | 2005 Honda Odyssey

1 Answer

Replace side passenger mirror 2000 Honda Odessy Van EX


You need to remove the internal door panel, then you can see the screw to remove the side mirror. Sometime you need to remove the glass before you can reach the screw.

Mar 24, 2010 | 2000 Honda Odyssey

1 Answer

How do you replace a 2007 Honda Odyssey Tail Light


Yes, you have to remove the plastic panel. It is mostly held by spring clips. You can see how to remove it at the link below.
http://www.odyclub.com/forums/52-2005-2010-odyssey/52868-can-t-open-liftgate.html

Aug 20, 2017 | 2007 Honda Odyssey

2 Answers

Can an individual replace rear tail light housing on the liftgate


hi yes its not a problem make sure you clean the area where the mounting screws go in as that also acts as an earth good luck

Nov 16, 2009 | 2003 Honda Odyssey

1 Answer

How do you replace a brake light?


serjoijr: To replace the bulb, you must remove the tail lamp housing.
Open the tailgate. There are two screws which retain the lamp housing to the body. You can see them when you open the tail gate, One is near the top and one is near the bottom. They are a phillips head type screw.
Remove both screws and pull the lamp housing directly backwards. DO NOT TWIST IT TO THE SIDE! The housing has a pin on the opposite side which interlocks with the body, keeping it in place on that side.
Once you have pulled the housing away from the body, you will see the lamp sockets and wiring harness. These sockets usually rotate to one side or another to interlock with the housing. Once the socket is removed, you can replace the bulb and return the housing back to the original spot.

Jul 28, 2009 | 2004 Honda Odyssey

2 Answers

Removing rear light assembly on honda odyssey 2006


Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Jan 24, 2009 | 2007 Honda Odyssey

1 Answer

2003 Honda Odyssey Brake light replacement


open the rear hatch. Between the tail light housing and the rear hatch opening there is a trim strip with two flush fitted flap doors. Insert a small straight blade screwdriver into the small slot on the tail light side of the flap. Pry gently inboard and the small flap will open (the hinge side of the flap is on the side of the rear hatch opening.) Now you can remove the screws that hold the tail lamp assembly in place. Finally, there is still a "spear point" clip that fits into a socket near the front outboard corner of the assembly. Gently pry with a tape wrapped screwdriver (avoids scratches) and force the assembly straight back. The clip should release and free the assembly so you can change the bulb(s).

Jan 22, 2009 | 2003 Honda Odyssey

1 Answer

2004 Honda CRV tail lamp assembly


remove the grommet the wires go through, you may be able to reach the connector or remove inner trim panel.can you not use the original loom and just change the light unit?

Dec 29, 2008 | 2004 Honda CR-V

Not finding what you are looking for?
2008 Honda Odyssey Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...