Question about 2006 Dodge Ram 1500

Open Question

P1128 and p1129 codes dodge ram

Changed O2 sensors about 2 month ago and codes have been there ever since

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: P0406 Code on '05 Dodge Ram Hemi 5.7

this is a egr problem lack off flow

Posted on Jan 25, 2009

polarcycle
  • 1392 Answers

SOURCE: I'm getting code P0138 on '99 Ram

Could be just the sensor, could be a bad fuse, or could be bad wiring. Change the sensor, check the fuse, and check wiring, or reverse order.

Posted on Jun 05, 2009

  • 335 Answers

SOURCE: code p0138 for the second time

P0138 is code for o2 sensor Bank 1 Sensor 2. This sensor is the one behind the cat on the side of the engine that contains cylinder No 1.

Posted on Jun 15, 2009

  • 36 Answers

SOURCE: how do i locate o2 sensor on 2003 dodge ram 1500

Which one? They are in the exhaust pipes under the truck. Only wires going to the exhaust.

Posted on Nov 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Dodge Ram 1500 code p1128 and p1129


The prevalent cause is the fouling of the O2 sensors in the exhaust pipe and the catalytic convertor(s). This usually caused by the fuel not burning correctly in the combustion chamber. And this can be caused by: bad/no spark in combustion chamber due to weak plugs or electrical going plug coil packs; partially plugged fuel injectors and result being too much un aspirated fuel entering the combustion chamber; bad or old fuel, improper fuel octane for engine.

Suggest you fuel up asap with PREMIUM fuel (for 1 tank) and 1 can super concentrated injector cleaner for next 2 tanks. Check air filter clean. Check air intact air analyser sensor wire is clean, pull the plugs and check condition and gap, replace them if fouled or worn.

Oct 14, 2014 | Cars & Trucks

1 Answer

CODES P0300, P1128


po300 is random miss fire doubtful two O2 sensors bad at one time most likely coolant temp sensor is bad causing engine to run rich this will cause O2 sensors to throw a code(thats what they are there for..exhaust gas temp. and raw fuel) running rich will also fowl spark plugs(=miss fire) P1128 ??

Mar 20, 2013 | 2006 Jeep Liberty

1 Answer

1996 honda accord o2 sensor versus Catalytic converter codes p0135 and p0141


The fault code P0135 means O2 Sensor Heater Circuit (Bank 1 Sensor 1)
The code P0141 means O2 Sensor Heater Circuit (Bank 1 Sensor 2)

Launch X431 Connector

Aug 22, 2012 | 1996 Honda Accord

1 Answer

Car running lean on bank 2, changed intake gaskets and pcv valve


what does exhaust smell like you may have carbon build up in engine try removing o2 sensors and cleaning with brake clean and reinstalling reset code and see if it comes back and how long it takes to reset also you can put a can of berryman in the gas tank with at least 1/2 tank of gas or more also buy a can of sea foam and install through vacuum booster hose you may see lots of black smoke from tail pipe if so after following instructions for application drive some what hard and if the black smoke continues fore at least a mile keep driving and if you notice a diff in runability but still have a little black smoke buy another can of sea foam and repeat service NAPA has sea foam on sale this month

Apr 11, 2012 | 1996 Chevrolet Impala SS

1 Answer

Code po301 then two weeks later po133 came up on my actron car runs rough and stals out i changed o2 sensor on back of motor a month ago, plugs and wires.


Change both front sensors-- if you have dual exhaust

What about the PO301 ?
That is a misfire on cylinder #1

Your old O2 Sensor, that was slow to respond,
as well as a misfire, shouldn't cause a stall

You had 3 problems

Apr 02, 2011 | 1999 Pontiac Grand Am GT

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

1 Answer

Have error codes 1128 and 1129 what causes these codes


P1128 - Closed Loop Fueling Not Achieved - Bank 1
P1129 - Closed Loop Fueling Not Achieved - Bank 2
Found for 2007 Dodge Ram 1500 5.7L

Feb 09, 2011 | 2007 Dodge Ram Truck

1 Answer

What do the codes 1128, 1129, 1133, and 1134 mean on my Porsche Boxter 2001?


code P1128 02 sensor bank 1 lean
code P1129 02 sensor bank 1 lean to limit
code P1133 02 sensor bank 2 lean
code P1134 02 sensor bank 2 lean to limit

fuel system is lean.

Jan 29, 2011 | 2001 Porsche Boxster

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...