Question about 1997 Dodge Avenger

Open Question

The bright lights, turn signals, and windshield wipers don't work and all fuses working

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 46 Answers

SOURCE: Headlights Not Working, Brights and Turn Signals Work

This is cuased by the multifuntion switch that is located on the steering column. It is the swith with the headlight dimmers on it.

You just need to remove the steering column bezels and replace the multifunction switch.

Posted on Aug 29, 2008

Ad
MrScary66613
  • 1990 Answers

SOURCE: 2001 dodge intrepid wind shield wipers not working

There is a Fuse for the Wipers on the Box inside the Car. There actually could be one in the Relay Fuse Box under the Hood also. This box Shoud be on the Drivers Side up torwards the Firewall of the Car.

Posted on Jan 25, 2009

  • 192 Answers

SOURCE: can't find fuse box for horn,turning signal and windshield wiper

I looked this up on WikiAnswers. Apparently the 2005 dodge magnum has 2 fuse boxes. One is under the hood on the passenger side and the other is in the trunk, next to the battery, in the spare tire storage well.

Posted on May 11, 2009

motor1258
  • 6674 Answers

SOURCE: windshield wiper fuse blows everytime I turn the ignition on

Try removing the harness connector to the motor, and see if it still blows the fuse, then you've isolated the problem.

Posted on Jun 05, 2009

c17hydro
  • 2984 Answers

SOURCE: turn signal not working, but wiper are working

You have two locations, one is under the hood of your engine and the other is a kick panel location on the driver's side by the parking brake. This is the picture for the fuse block and the kick panel location and engine fuse block.

Please don't foget to rate:

2cfa54f.gif
79a47d4.jpg
53808db.jpg

Posted on Jul 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

My 2003 mitsubishi lancer es standard 5 gears signal lights arent working neither are my bright lights and my windshield wipers only are working on high ?


Sounds like a bad fuse. There are fuse boxes under the hood as well as inside. Try swapping the same number fuses with each other. If what you swap for starts working replace the fuse you swapped with. Alot of times there is a fuse puller in fuse box case and spare fuses.

Aug 15, 2013 | 2003 Mitsubishi Lancer

1 Answer

The directional light, wipers, brights, are not working


the combination switch may be bad. (wipers, turn signal, hi-lo beam switch)

Oct 13, 2009 | 2008 Dodge Avenger

1 Answer

2004 monte carlo. Turn signals dont work. The stalk still works with other functions, such as wiper, brights. The fuse is fine. Could it be a bad relay? When u push the stalk up or down nothing happens on...


try pressing the hazards on and off if they still don,t work replace the flasher unit. it is built into the hazard switch( all one unit ) change this and all will be good.

Aug 30, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

My headlights,windshield wipers, and turn signals wont work


check all your fuses. replace any and all bad ones. if fuse blows again u have a short somewher

Jul 02, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Dash and shifter lights in 1996 jeep cherokee wont light


Hello and welcome to FixYa . Locate the dial that controls the brightness of the dashboardlights. If the control is not immediately evident. Make sure the brightness control is turned on. If it is and the lights aren't working, the problem may be a bad fuse. Check the fuse that controls the dashboard lights Replace the fuse if necessary. If just one part of the instrument panel is not lighting up, then you have either a burned-out bulb or a wiring problem.

Passenger side kick panel fuse breakdown for a 1996 jeep Cherokee Country

01 - 25A Rear Wiper/Washer
02 - 15A Radio, Cigar Lighter
03 - Empty
04 - 15A Passing Light
05 - 30A Blower Motor
06 - 30A (Circuit Breaker) Power Windows
07 - 02A ABS
08 - 20A Turn Signal Flasher
09 - 10A Radio/Clock Memory, Courtesy Lights, Glove Box, Cargo, Dome Lights, Telltales
10 - Empty
11 - 25A Headlamp Delay Module, Horn
12 - Empty
13 - 20A Power Door Locks
14 - Empty
15 - 15A Instrument Panel Lamps, Clock/Radio and Memory, Headlamp Switch, Parking Lamps
16 - 30A (Circuit Breaker) Power Seats, Trailer Tow
17 - 7.5A Instrument Cluster Gauges, Headlamp Delay Module, Chime Module, Overhead Console
18 - 25A Rear Defrost
19 - 05A Instrument Panel Lamps, Radio Illumination
20 - 5.5A (Circuit Breaker) Windshield Wipers and Washers

This should get you going. And you can always Ask Me.

Apr 27, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Signal and windshield wiper aren't working


switch in steerig console combo wiper turn?

Mar 01, 2009 | 1999 Volkswagen New Jetta

Not finding what you are looking for?
1997 Dodge Avenger Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...