Question about Cars & Trucks

Open Question

Remove engine cover 2002 thunderbird - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford Thunderbird: Were are the Cam Position Sensors


It is located at the top rear of left cylinder head

Sep 10, 2016 | 2002 Ford Thunderbird

1 Answer

Will Thunderbird mustang ford mercury v6 ford heads ford head


Depends on whether the Thunderbird engine is a V-6. it is a 4.0 V-6.and what year. Take your head gasket off the Explorer engine and place it on the head off of the thunderbird head, if all the holes line up its possible, check and see if the valve train are the same. Are the head bolts in the same place. And as you know, you will have to buy new head bolts to install the heads if they work. They say not to use old head bolt twice. They have been stretched and could break.

I hope this has help you on your project. Good luck.

Feb 19, 2014 | 2002 Ford Explorer

2 Answers

2002 Ford Thunderbird turns over but won't start


Check for fuel at engine and for spark at coil

Nov 26, 2012 | 2002 Ford Thunderbird

1 Answer

Where are thr coils located on a 2002 thunderbird


Right side ignition coils----Remove the air cleaner outlet tub.
Left side ignition coils------Remove the evaporative emission canister valve.

michael_cass_253.jpg

Jul 05, 2011 | 2002 Ford Thunderbird

1 Answer

2002 Ford thunderbird will not hold charge in battery jump starts ok but after shuting it down it will not start back up. does not seam to be recharging the battery. were can i find a how to to change...


It may be a bad alternator. After jump starting the engine and while idling, remove the negative terminal of the battery. Observe if the engine dies, then the alternator is bad.

May 16, 2011 | 2002 Ford Thunderbird

1 Answer

Instructions on changing the timing cover gasket on a 1991 ford thunderbird with 3.8 liter v6 engine


first you have to diconnect throttle cable and trans kick down from throttle body. than disconnect wires and vacuum hoses and remove upper intake manifold plenum. that should give you access to valve covers . Remove bolts from covers and change gaskets. also replace the gasket on the upper intake plenum. install items in reverse order of removal. keep track of vacuum lines where the go when you remove . mark with tape their location.

Nov 08, 2009 | 1991 Ford Thunderbird

1 Answer

I cracked my oil pan and i need to know if i need to take out my engin to change it i'm low on cash i need help


here's v6 3.8L

Section 03-01A: Engine, 3.8L 1996 Thunderbird, Cougar Workshop Manual
IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Disconnect battery ground cable (14301).
  1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12 .
  1. Remove two bolts retaining radiator upper sight shield (8C291) and position radiator upper sight shield aside.
  1. Remove hood weather seal.
  1. Remove windshield wipers.
  1. Remove LH cowl vent screen and wiper module.
  1. Install Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Remove front engine support insulator through-bolts.
  1. Partially lower vehicle.
  1. Raise engine and support with Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle.
  1. Remove starter motor (11002).
  1. Position drain pan.
  1. Drain engine oil.
  1. Remove oil bypass filter (6714).
  1. Remove starter motor wire, ground strap and automatic transmission oil cooler lines.
  1. Remove oil pan-to-bell housing bolts and bolts at crankshaft position sensor lower shield.
  1. Remove remaining oil pan retaining bolts.
  1. Remove steering shaft pinch bolt and separate steering shaft.
  1. Position transmission jack under front sub-frame (5C145).
  1. Remove six rearward bolts on front sub-frame. Loosen two forward front sub-frame bolts.
  1. Remove lower shock absorber-to-front suspension lower arm bolts and nuts (both sides).
  1. Lower front sub-frame.
  1. Remove oil pan (6675).
  1. Empty any residual oil from oil pan.
  1. Remove oil pump screen cover and tube retainer bolts and support bracket nut. Remove oil pump screen cover and tube (6622) and discard oil pump inlet tube gasket (6626).

Apr 14, 2009 | 1996 Ford Thunderbird LX

1 Answer

Where are the plugs on a 02 ford thunderbird


Each valve cover has a removable top, held by seven 7mm screws. Spark plugs are under coils.

Apr 09, 2009 | 2002 Ford Thunderbird

1 Answer

2002 ford thunderbird 3.8 engine. misfire .


its a 3.9 engine and the cure is to replace with valve cover gaskets and new spark plug grommets new part numbers apparently fix the problem to prevent from reoccuring.

Nov 16, 2008 | 2002 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...