Question about 2001 Ford Windstar

Open Question

2002 ford windstar belt replacement - 2001 Ford Windstar

Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 337 Answers

SOURCE: 2002 ford focus timeing belt set up

Posted on Dec 07, 2008

  • 1068 Answers

SOURCE: 2002 Ford Windstar Error Code P1131 And P1151

those two codes are for the o2 sensors. both are the upstream sensors on the front and rear banks. so they are desinagted bank 1 sensor 1 and bank 2 sensor 1. them most common cause for this is faulty o2sensors , bad gas and of a poor running engine. so if your car runs good (no misfire) and gas is ok then replace the o2sensor witch is the very most common cause.

Posted on Jan 28, 2010

Testimonial: " Help With Problem But Where Are These O2 Sensor"

  • 46 Answers

SOURCE: 2002 Ford Windstar serpentine belt diagram 3.8 L

3c667a9.gif I hope this helps you

Posted on Aug 19, 2010

Testimonial: "Thank you very much. It is a passenger van but I think its the same. Thanks again."

  • 17970 Answers

SOURCE: need belt routing diagram for 2002 ford windstar

Check this...


(click over pic for additional details)

I hope helps; remember to rate this.

Posted on Oct 05, 2010

  • 147 Answers

SOURCE: Instructions needed for changing serpentine

  • the serpentine belt routing chart, adhered to the fan shroud. This chart will show you the location of the belt tensioner.
  • 2 Pull the belt tensioner off the belt with the serpentine belt tool. Reach in with your free hand and slip the belt out of the tensioner's path and then slowly move the tensioner back into position.
  • 3 Pull the belt off the remaining pulleys by hand

  • Read more: 2002 Ford Taurus Serpentine Belt Removal '

    Posted on Sep 09, 2011

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    How to adjust TENSIONER pulley on 2002 ford windstar

    2002 Windstar has a 3.8 litre engine, on this engine there is an automatic belt tensioner. The tensioner pulley is a the small one under the power steering pulley, yes, it's that small one way back there that is hard to get at. To remove the belt you would use a 15mm wrench on the belt tensioner pulley nut and rotate counterclockwise, when released it automatically tensions the belt, if you are hearing a squeal, look at the belt carefully and try to determine if it is running straight or one of the pulleys might be a little out of line causing the belt to lean away from its straight run. The problem here is usually the belt tensioner assembly is worn and needs replaced ( the whole assembly ) along with a new belt.

    Jul 31, 2012 | 2002 Ford Windstar Cargo

    1 Answer

    Routing for belt for a 2002 ford windstar

    Check this previous answer: need_serpentine_routing_diagram.

    Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

    Thank you for using Fixya, and have a nice day.

    Nov 01, 2011 | 2002 Ford Windstar Cargo

    1 Answer

    Need belt routing diagram for 2002 ford windstar

    Check this...


    (click over pic for additional details)

    I hope helps; remember to rate this.

    Oct 05, 2010 | 2002 Ford Windstar Cargo

    1 Answer

    03 windstar cherp or squeal from top of engine removed belt noise still there sounds like cam how can I fix

    2002 Ford Windstar 3.8 223000kms engine squeal or chirp with serptine belt removed.

    Jul 07, 2010 | 2001 Ford Windstar

    1 Answer

    My 2002 ford windstar has a leak comming from the pipe thats connected to the water pump and now my belt has broken and the waterpump I believe is frozen. can a waterpump freeze from having water put into...

    i think your water pump is done for. replace pump and the belt and you should be good to go. that lower pipe always rotts out on these vans. might want to replace the coolant bypass hose on top while your at it. it tends to brake around the same time as the lower pipe

    Feb 15, 2010 | 2000 Ford Windstar

    1 Answer

    I need a serpintine routing diagram please for a 2002 ford windstar.


    Drive Belt Routings


    Fig. Accessory drive belt routing-3.0L engine


    Fig. Accessory serpentine belt routing-3.0L engine


    Fig. Accessory serpentine belt routing-3.8L engine

    I hope help you with this. Good luck.

    Sep 14, 2009 | 2002 Ford Windstar Cargo

    1 Answer

    Serpentine belt

    possibly. was ir screeching before you replaced the belt?

    Sep 03, 2008 | 2002 Ford Windstar Cargo

    Not finding what you are looking for?
    2001 Ford Windstar Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts


    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers


    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides