Question about 2003 Nissan Primera

1 Answer

Car want start after replacing cam sensor - 2003 Nissan Primera

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 52 Answers

If this only happened when you have replaced cam sensor then it could be wrong or faulty, check the resistance with tester

Posted on Apr 16, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am going to replace cam sensors because i replaced crank sensor and it has a hard start but it will start


Hi Maliasa replacing sensors is not the answer cam sensors will not prevent starting get someone to plug in your car and diagnose it properly. Otherwise you will spend a fortune on sensors. Regards Jim...

Jun 11, 2015 | 2003 Nissan Maxima

1 Answer

2003 dodge Dakota 4.7l. High mileage. OBDII throwing a new code everytime I fix something. Crank sensor & Cam sensor - replaced. IAC-replaced. PCM-replaced. Throttle body cleaned. O2...


Have you checked the wiring that goes to both the Crank and Cam sensors? Most of the time the wires are close to a heat source (ie: exhaust manifold) and the plastic covering starts to melt causing the cooper on wires to make contact and thus making engine stop, you will have to take off the protective covering as well as tape around the wires and inspect each and every one. Had same problem with Dodge caravan, it turns out the Crank Sensor plug wires were melted together. Good Luck.

Oct 26, 2013 | 1993 Dodge Dakota

1 Answer

Code p1391 99 grand cherokee limited 4.7 wont start


Try unplugging the cam sensor and then try to start. The cam sensor is on the underside of the passenger head towards the front of the engine. Is is accessible from under the vehicle. If it starts replace the cam sensor. Iffy it still does not start replace the crank sensor and the cam sensor. The crank sensor is located on the passenger side of the engine block behind the starter. The starter will need to be remove to acces the sensor. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Mar 11, 2012 | Cars & Trucks

1 Answer

I have a 1995 chevrolet blazer that wont started by cranking it but it will start when u spray gas in to it and we replace the fuel pump. what could make this happen?


The injectors are pulsed from the cam ,and the crank sensor,the cam sensor starts the pulse,so I would suggest replacement of the cam sensor.

May 26, 2010 | 1995 Chevrolet Blazer

1 Answer

Car wont start


being 94' im sure it has high miles, cam and crank sensor common to fail over time do to wear and heat exposure. check the basic, make sure you getting fuel and sparks. fuel pump only work as long the engine is turning over due to the crank sensor sense the flywheel turning. crank sensor may be faulty. no sparks, check coil make sure is good and putting out 12v, auto zone can test it for free. good coil, than check cam sensor, cam sensor senses the cam turning and tell the ecu to tell the coil to disperse the sparks to the plugs. cam and crank sensors, there no way of testing it but replacing the unit unless you have the special equipment to test it; both is fairly cheap to replace, check ebay.

Oct 24, 2009 | 1994 Mazda MX-6

2 Answers

Cam shaft sensor replaced


the crankshaft sensor needs to be replaced.you could have purchased a faulty sensor,

Jun 12, 2009 | 2004 Dodge Stratus

1 Answer

2003 stratus both sensors replaced still unresolved


Have the exact problem. Replaced cam sensor and timing belt. Still happens intermittently. code is p0344.

May 30, 2009 | 2003 Dodge Stratus

2 Answers

Car stalls while driving


you have a bad crankshaft sensor. replace the crank sensor.

dodges and gm's are known for this problem.

Apr 10, 2009 | 1998 Plymouth Neon

2 Answers

2001 concorde dont start


Check the cranshaft position sensor located under the timing cover. Also check the camshaft sensor located near the camshaft.

Feb 06, 2009 | 2001 Chrysler Concorde

Not finding what you are looking for?
2003 Nissan Primera Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...