Question about 2000 Lincoln Navigator

Open Question

How to program or link your garage opener on your sun visor

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: 2007 Lincoln Town Car Limited-can't program garage door entry key

ok

Learn Mode
ani_caut.gif WARNING: A garage door opening system that cannot stop or reverse itself after detecting an object in its path does not meet current federal safety standards. To decrease the risk of serious injury or death, do not use the universal transmitter with a door opening system that lacks stop and reverse features as required by federal standards. This includes any garage door opening system manufactured before April 1, 1982.
ani_caut.gif CAUTION: During this procedure, the system that you are programming will be made to operate. Make sure that people or objects are clear of the garage door or gate being programmed.

  1. Select a universal transmitter button to train.
  1. NOTE: If more than one button is pressed, priority will be given to the lowest numbered channel.
    Press and continuously hold the button for 20 seconds. CHANNEL X TRANSMIT will be displayed (X will be 1, 2 or 3) during this time.
  1. NOTE: If the channel being trained has not been previously trained, the channel will immediately enter training mode (no 20 second delay).
    After 20 seconds, the display will read CHANNEL X TRAINING to indicate training has started.
  1. Point the original garage door opener transmitter at the overhead console. Hold down the original transmitter's transmit button so the overhead console can learn the original transmitter's frequency and data stream.
  1. Training will be completed in 100 seconds or less. CHANNEL X TRAINED will be displayed when training is complete. DID NOT TRAIN will be displayed if the channel did not correctly train.
  1. NOTE: Additional training may be required for rolling code equipped devices. For additional information, refer to Rolling Code Programming in this section.
    Release the channel X button. Training is complete.
Rolling Code Programming
NOTE: To train a garage door opener (or other rolling code-equipped devices) with the rolling code feature, follow these instructions after completing the learn mode.
  1. Locate the learn or smart button on the garage door motor head unit. Exact location and color of the button may vary by product brand. If there is difficulty locating the learn or smart button, refer to the device's Owner's Literature.
  1. Press and release the learn or smart button on the garage door motor head unit.
  1. NOTE: Following the previous step, there are 30 seconds in which to proceed.
    Press and release the programmed universal transmitter button. Press and release the universal transmitter button a second time to complete the training process. (some garage door openers may require this procedure to be done a third time to complete the training.)
Transmit Mode
  1. Select the button for the desired channel (for example, for the garage door you wish to open).
  1. NOTE: If more than one button is pressed, priority will be given to the lowest numbered channel.
    Press the button. CHANNEL X TRANSMIT is displayed.
  1. The correct signal is transmitted to the device being controlled.
  1. Release the button.
Erase Mode
  1. Simultaneously press and hold buttons 1 and 3 for 20 seconds.
  1. CLEARING CHANNELS will be displayed while the channel codes are being erased.
  1. CHANNELS CLEARED will be displayed when the erase operation is complete.
  1. Release buttons 1 and 3.
Universal Transmitter Default Code Mode Loading
  1. Press and hold buttons 1 and 3 simultaneously. CLEARING CHANNELS is displayed.
  1. After 20 seconds, CHANNELS CLEARED is displayed. Continue to hold buttons.
  1. After 10 more seconds, CHANNELS DEFAULTED is displayed when the default codes have been successfully loaded

Posted on Dec 31, 2008

johnjohn2
  • 5763 Answers

SOURCE: i need instructions on how

This should be done by pushing the button on the garage door motor as you would program an opener, push the program button then push and hold the button on the visor for a few seconds then release, push again and door opener should operate.

Posted on Sep 13, 2010

sodeep
  • 3267 Answers

SOURCE: remote door opener

So, you get out your remote control to your garage door opener and, then get your owners manual to your new car. You need to follow the instructions from the manufacturer to be able to program the remote control to the car.

Ok, you have followed the instructions from the car manufacturer and you press the button for the garage door to go up.......and nothing happens. So, then you think you have missed a step on the programing. Well, what most instruction manuals leave out is the step from programing the car/truck/van to the garage door machine itself. On the back side of your garage door opener is a panel called the logic board. The logic board is the computer or brain of the machine. Most new garage door openers now are a mulit-code machine. By that, i mean it uses several signals each time you press the button on your remote control. This is for security, so your code can't be stolen by a code-grabber.

Now, comes the step of programing the vehicle to your garage door opener. Once you have followed the instructions of programing your vehicle, you now have to "teach" the car to the garage door opener. You will need some help doing this. You will have to get someone to press the button in your vehicle and hold it down, while someone else has to press the learn button on the back your your garage door opener mounted on the ceiling. The learn button on the back of your machine will be square if using a liftmaster machine. Craftsman, Liftmaster, Chamberlain are all the same. Their learn buttons are square, and usually are yellow, red/orange, or purple. If using a Genie, it has a button that says "learn button".

The person pushing the button on the machine will only have to push and release the learn button. DO NOT hold this button down. If you do, it erases all of the programing in the machine, and you have to re-program all the remote controls that you have. You will have to read my other hub to find out how to do that. You will probably say a few words you shouldn't either. :-) Programing the vehicle to the machine only takes a second, and when the machine accepts the code, the light bulb on the machine should flash for a brief moment, and you should hear audible click. Yep, it's that easy! I dont know why the auto makers leave that step out. Anyway, i hope this helps, and if you have any questions.. leave them in my comments and i will try to walk you through it. See the photo above and you will see the typical logic board...the square red/orange learn button is easy to see. Just remember to press and release

Posted on May 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to sync 2002 volvo s60 garage door opener with garage


Hold any of the buttons down while you press the door opener remote and wait for alight in the dash to flash that the code has been learned by the car. You may also google "HOMELINK" programming for more info.

Aug 28, 2012 | 2002 Volvo S60

1 Answer

What are the three buttons for that are on the drivers side sun visor?


they make it possible for you to program your automatic garage door opener to open using them-'home link' the older ones (probably like yours)do not work with 'rolling code' door openers, but if you have an automatic door opener, you can try to program the controller to work with it.

Mar 10, 2011 | 1996 Chrysler Cirrus

1 Answer

There are 3 buttons on the sun driver side visor, what do they do? when I push any of the, a light lites next to it?


these should be programable buttons for a garage door opener setup in your car...they can be set to the frequency of a garage door remote....

Jan 11, 2011 | 1997 Jeep Grand Cherokee

1 Answer

How do I program the garage door opener on the sun visor?


Directions are in your owners manual. Most are done by holding down the sun visors button until it flashes, then hold your opener next to the visor and push your openers button.

Sep 22, 2009 | 2000 Volvo S70

1 Answer

Need to program/link garage door opener with the one on the visor in the car


Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

May 29, 2009 | 2006 Audi A4

3 Answers

How to program the volvo V 70 XC 2008 garage door opener


Simply hold down the button you want to use (there are 3 for up to 3 different garage doors) until the light flashes and keep holding it down. Now place the garage door opener up near the sun visor and hold it's button down until the light on the on button you are programming flashes. It is now programed. The other 2 are done the same way. Good luck. It took me a while to find the info, it's not in any Volvo manuals I could find.

Mike

Apr 26, 2009 | 2008 Volvo XC70

2 Answers

Three buttons on drivers side sun visor


ok, this other guy has the buttons your talking about confused with 3 buttons on the drivers side door panel, just above the handle...
the buttons you are looking at on the visor are programmable to open your garage door...however since i've never owned a garage door that i use at the same time i've owned my grand cherokee, i have never tried setting it, so i'm not exactly sure how to go about that...

Mar 28, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Lincoln Navigator Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...