Question about 1994 Mazda 2WD B Series Pickup

Open Question

Had air in hydraulic line bled off clutch wont disengage

Had air in clutch hydraulic system.bled off .now transmission wont engage

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 420 Answers

SOURCE: I cant dis-engage my cluth on my 94 mazda b3000

Could be a throw out bearing or the shift fork is broke.

Posted on Sep 06, 2009

  • 1 Answer

SOURCE: 2005 rx8 clutch wont disengage

the rubber around the
piston are worn remove from gearbox and replace rubber seals

Posted on Apr 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont go into gear while driving has to be turned off then it will has new clutch


It sounds like the clutch is not disengaging when depressed. What is the year make and model? It most likely has a hydraulic clutch. Many vehicles have the clutch slave cylinder inside the bell housing of the transmission. This means that the fluid line to the slave cylinder was removed to remove the transmission. If a new slave cylinder was installed when the clutch was replaced (this is a good idea to do when servicing a clutch with a bell housing internal slave cylinder) then the system will need to be bled to remove air from the system and allow the clutch disengagement to function properly.

Mar 07, 2017 | Cars & Trucks

1 Answer

My 1999 accord wont shift into gear while its on but will when its off its a 5 speed.


It's your hydraulic clutch system that probably isn't working. When you press the clutch pedal down, it causes the clutch master cylinder to put pressure in the line to the transmission's little "slave cylinder" that operates the clutch inside the transmission bell housing. This disengages the engine from the transmission so you can shift gears. It's probably not putting the slave cylinder to work by hydraulic pressure. The clutch master cylinder is mounted on the firewall, similar to the brake master cylinder, the clutch cylinder has a reservoir and you may need to add brake fluid to it. If it is dry, then you will need the system bled at the slave cylinder by a pro or someone who understands how. Pretty simple, really, just like bleeding brakes. Also the clutch master cylinder can develop internal leaks and this will lead to loss of clutch.

Nov 02, 2015 | Cars & Trucks

1 Answer

Clutch would not disengage


IF you have bled the clutch system and managed to get a firm clutch then the clutch plate has been installed back to front and the clutch center is hitting the bolts that hold flywheel onto the crankshaft. If you have no not got a firm predal pressure replace the clutch master cyl

Mar 02, 2013 | 1989 Ford Ranger

1 Answer

94 Chevy 2500 Clutch Engagement?


You probably have a hydraulic clutch. A hydraulic clutch has both a master and a slave cylinder. The slave cylinder engages/disengages the clutch plate. You might be low on clutch fluid in the master cylinder, or the system may need to bled similar to bleeding brakes. Worst case is you need a new clutch, pressure plate, and throwout bearing. They should all be replaced when doing a clutch job.

Aug 23, 2012 | Cars & Trucks

1 Answer

Transmission issues


Typical Clutch Problem. Check to see if Clutch Linkage is Hydraulic or Mechanical. If Hydraulic then replace Clutch Slave Cylinder First.Bleed out air from Hydraulic line. if this doesn't fix it and or it has a Mechanical Clutch Linkage then Replace Clutch itself don't forget to get a new throw ou bearing and pack it with heavy duty grease otherwise in 20,000 miles you'll be doing it again. Thanks Keith

May 15, 2012 | 2004 Pontiac Sunfire

1 Answer

I have a 2000 chevy s-10 2.2 engine. I have to push all the way to the floor to shift and still have difficulty shifting gears. what might be my problem?


Your truck has a hydraulic clutch , that works just like brakes. A master cylinder connected to the foot pedal sends fluid to a salve cylinder inside the bell housing. If there is any air in the lines , the slave cylinder will not move far enough to disengage the clutch. The lines can be bled of air bubbles much the same way a brake line can be bled. Hopefully this is the problem. A worn out Master cylinder is not too big of a job to replace , however , on your vehicle the slave cylinder is inside the bell housing of the transmission , and replacing it would require removal of the transmission. If you are not loosing fluid out the slave cylinder it is probably ok.

Oct 18, 2010 | 2000 Chevrolet S-10

1 Answer

Replacing the clutch on a 1998 Saturn SL1 we encountered a problem after installation, The clutch would not disengage. The hydraulic clutch system and slave cylinder seemed to be working fine, we even...


It is very difficult for you to disengage the clutch by hand or with any leverage you can get outside the transmission. There is over 200 lbs of force clamping on the clutch disc.

If you replaced the clutch and took the slave cylinder out of the transmission without putting a brick under the clutch pedal or disconnecting the pivot arm from the pedal then you ruined the hydraulics. Buy a new PRE-BLED system from a local auto store. Generally this is the problem.

Either that or the clutch fork is bent or you installed the throwout bearing backwards (or simply fell off the fork which is not all that uncommon).

May 22, 2010 | 1998 Saturn SL

1 Answer

02 dodge 2500 clutch not releasing


An hydraulic clutch line can be bled. There should be a bleeder screw on the cylinder at the end of the line running from the master clutch-cylinder.

Charlie

Aug 14, 2009 | 2002 Dodge Ram Maxi

1 Answer

Clutch wont engage


With the hydraulic systems, there is no adjustment. So what pedal travel you have is likely normal for that vehicle.

May 30, 2009 | 1994 GMC Sierra

1 Answer

Fixing a clutch that suddenly stopped disengaging properly.


that is a hydraulic clutch and when they go out they dont always give warning. but it could be a leak in the line or just low on fluid and needs bled.

Jan 14, 2009 | 1992 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...