Question about GMC Envoy

Open Question

2004 gmc envoy blows ignition fuse when in 2wheel dr and taken out of park

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2004 Envoy AC works but does not come out the front vents. Only @ windshield

You most likely have a bad mode actuator. http://forums.trailvoy.com/showthread.php?t=40235

Posted on Sep 26, 2008

Ad
  • 1 Answer

SOURCE: power outlets dont work

I just purchased a 2002 Envoy and had the same problem. If you raise the drivers's side rear seat, you will see a big black box. Remove this box by pulling the bottom of the box outward and it will come straight up. Next you will see a black cover. This cover has a push tab on each end. Push
the tabs at the same time and lift up on the cover and it can be removed. Inside the cover there is a fuse diagram. The fuse number for my 2002 was #46. This fuse controls the front plugs and #15 controls the back plugs. Locate the the fuse puller on the top left, then count over to spare fuse #3. Between #3 and #4 the fuse is located about 1 1/2 inches below those fuses. You will see a yellow 20 amp pin fuse (BP/ATM-20RP AUTOZONE). remove and check fuse.

Good luck

Rick

Posted on Jan 07, 2009

  • 250 Answers

SOURCE: battery removal on a 2004 GMC Envoy

The battery is on the right side behind the fuse box. You need a metric set to undo the 3 screws. Theres one that attaches to the body, one to the bar that goes along the top, and theres one on the left side below the vacuum hose and air induction. After you've taken out those three, you should lift the whole thing out(battery and shroud) together. It's hard to take the shroud off before you lift the battery out. After that, you have to pry the shoud off the battery. The two terminals in the back make it hard. Then just go to any auto parts store and they'll give you a new one. 

Posted on Jan 28, 2009

  • 43 Answers

SOURCE: the gear shift on my 2004 gmc envoy does not move from park.

cheak the brake pedel swich it work a swich in the gear seleter

Posted on May 26, 2009

  • 85 Answers

SOURCE: Where is the cruise control fuse for GMC Envoy

its in the fuse panel under the hood there should be a chart on the cover

Posted on Feb 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 gmc envo when engine is off and in park headkights stay on


Do they stay on after key is removed from ignition lock cylinder ?

Check HDM relay 46 in the under hood fuse / relay box . Relay contacts stuck closed , possibly ! The relay supplies B+ voltage to the low beam fuse's ! Let me know if that works or not . If not , will go on too more diagnostics steps .

Jul 31, 2016 | 2004 GMC Envoy XL

1 Answer

Key stuck in 2004 gmc envoy and car will not start


make sure battery is 12.6 volts. if not you not going to be able to get transmission go all the way in park to remove ignition key.when you press brake pedal it energize brake transmission shift interlock to get transmission all way in park to remove ignition key.if all is good battery is 12.6 volts.sound like ignition switch lock cylinder broken more likely.

Nov 06, 2011 | 2004 GMC Envoy

2 Answers

My 2004 envoy starts but there is no electrical. the windows radio tail lights reverse lights dashboard lights ac heat dondoesnt work. but the odometer still works so there is electric and all the fuses...


Sounds like a bad ignition switch. There are 3 main ignition circuits coming from the switch, and one will control the engine and starting. One circuit is probably dead thru the switch, causing all the accessories to not function. I would tr that first.

Feb 23, 2011 | 2004 GMC Envoy

1 Answer

My 2004 gmc envoy, will shift into 4wheel drive high and low, but will not shift into 2wheel drive high. Is there anything I can try before I have to take it in to a repair shop ?


I would say it is the encoder motor. Had a similar problem on a Blazer. Had that replaced and it solved the problem. Could be the same on the Envoy.

Feb 14, 2011 | 2004 GMC Envoy

1 Answer

05 envoy is stuck in park,its not the fuse


stupid question, but are you sure you have your foot on the brake before you try to disengage park?

Jun 08, 2009 | 2004 GMC Envoy

1 Answer

Veh wont start


by looking at the wiring diagram for your truck. the pcm1 fuse only feeds the pcm so most likely it is a grounded wire between the fuse block and pcm. follow the wire harness closely between the two and see if its grounded somewhere. also try disconnecting the pcm and see if the fuse still blows. that would isolate the problem to the wiring. it is highly unlikely that the pcm would cause the problem.

Nov 27, 2008 | 2004 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...