Question about 1970 Buick Skylark

Open Question

Oil pan removal on a 1970 buick skylark - 1970 Buick Skylark

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: How do I remove the oil pan on my 1991 Buick

if theres a cross bar the engine will need to be removed.
if not just remove all the bolts around the oilpan and remove it.

Posted on Jun 12, 2009

  • 30 Answers

SOURCE: Removal of serpentine belt on a 1996 Buick automobile?

check if it has a tensioner, it look like a useless pully and put a breaker bar on it and pull it and the belt should loosen up, if theres no tensioner the alternator should have bolts to loosen up the belts.

Posted on Jun 27, 2009

  • 2841 Answers

SOURCE: I had asked about the check oil light coming on

I know nothing of a sensor in the oil pan. What you need to check is the oil pressure sending unit. The unit will look like this. 2c49e3a.png
Check the connection at the sensor to make sure it is secure before replacing. If you find it is leaking it for sure needs replacing. The unit will be located in a location like this on which is a 1995 Buick. 2a08cb5.png

Posted on Jul 24, 2010

  • 1051 Answers

SOURCE: How do you remove the

It's not uncommon for the oil pan to get stuck. This usually happens if the gasket was not put on correctly and gunk gummed up the seal, essentially gluing it in place. Use a small nylon, wood or leather covered hammer and tap around edge of pan. (use a lot of light taps to avoid denting the pan). Continue tapping until oil pan comes free. Don't try to pry off as this will deform the pan causing an uncontrollable oil leak.

Posted on Oct 27, 2010

  • 3640 Answers

SOURCE: how do i remove the oil pan from a 96 buick regal

I was told it's about a 3 hour job to change the oil pan gasket (on a '95 Regal w/3800 ). It says you must disconnect the power steering lines (because they run along the frame by the oil pan and get in the way), drop the subframe, and raise the engine to get the oil pan off. good-day ! thats GM for ya!! lol, The frame is in your way and the only way to get it out is to move the frame.

Posted on Jun 28, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


go to google and type in "Take Off Oil Pan For A 95 Buick Skylark"
you will find instructions there.

Oct 14, 2014 | Buick Skylark Cars & Trucks

1 Answer

How do you replace oil pan on a 1998 Buick Skylark?

you will have to jack motor up so you can clear oil pump.

Jun 15, 2012 | 1998 Buick Skylark

1 Answer

I need help replacing my starter on my 1995 buick skylark custom. I can't even locate it.

The starter is located net to the engines oil pan on one side of the engine

Jun 30, 2010 | 1995 Buick Skylark

1 Answer

How do i remove the transmission filter on a 1995 Buick skylark

Lots of the newer vehicles don't have a filter. The older ones do and are accesed by removing the transmission pan.

Apr 13, 2010 | 1995 Buick Skylark

1 Answer

How do I remove the thermostat from a 1995 buick skylark quad 4

remove the exhaust manifold
remove 2- 8mm bolts at coolant pipe flange
now the coolant pipe that runs under the oil pan remove the bolt at the front of the oil pan lower the pipe down
t-stat is in the top of that pipe at the flange

Apr 11, 2010 | 1996 Buick Skylark

2 Answers

Oil filter

Inside of the oil pan. Yep, I got one too.

May 02, 2009 | 1990 Buick Skylark

3 Answers

Replace belt tensioner pulley on 1994 buick skylark

You need to put a piece of wood underneath the oil pan and place a jack underneath the oil pan/motor, loosen the motor mounts that are next to the belts, then raise the motor enough to reveal the nuts/bolts for pulley...just dont raise the oil pan so high that you crush it or break something, only enough to be able to reach tension pulley...

Dec 21, 2008 | 1994 Buick Skylark

Not finding what you are looking for?
1970 Buick Skylark Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides