Question about 1992 Dodge Power Ram 50

Open Question

Engine will not start and now the engine will not turn over after installing a new fuel pump.

Backed out of garage and engine quit. Would not start. Fuel solenoid would click but no hum of the fuel pump. Replaced fuel pump and now the engine will not crank and still no hum in the fuel tank. Haven't done a thing under the hood.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rockitman187
  • 2559 Answers

SOURCE: 2007 Dodge Caliber will not start

Yes,They usually fail that quick

Posted on Jun 01, 2009

Ad
jmgldsmth
  • 1889 Answers

SOURCE: 96 Dodge Intrepid ES, engine stalls

Find your firewall electrical junction block (where all the wires enter the cabin on the passenger side) and with a zip tie pull up the wire bundle so it does not ride on the upper tie rods and, fasten the zip tie to anything that is solid in the engine compartment and, let me know what happens

Posted on Jun 01, 2009

MNfisherman
  • 11896 Answers

SOURCE: 1992 Dodge Grand Caravan engine failure

There is not fuse for pump but a relay in the relay block. I do suggest jumping to see if pump turns on. Test voltage from ECM if needed. If voltage is to pump, then pump is shot. If not voltage, relay may be bad

Posted on Sep 11, 2009

  • 153 Answers

SOURCE: 1994 dodge ram van b250. when warm, starts

Sounds like the fuel pump is going out. Its inside the tank. But first see if the fuel pump is clooged. take it off and see if its plugged. Check fuel pressure if you can. should be 45-55 psi

Posted on Oct 13, 2009

  • 5 Answers

SOURCE: Where is the fuel pump relay on a 1990 Dodge

It is a black box on the driver side mounted to the fender.. Black box.. what is your pickup doing? I would pull teh computer an take it in to a Dodge Dealer ship to have them Test it! and check at your local junk yard for the computer. good luck hope you figure it out!

Posted on Jun 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1989 s 10 pickup with 4.3 engine. About a month ago I was going to do my paper route here in town so I started it and backeds it out of the garage and left it run as it was about -20 and it was...


check the fuel pressure,that will tell you how healthy is the pump,with the key on/engine off,and then with engine running,need to find out what the pressure should on your year,it is not just the millage that affect the pump,the age and how many time in life the car , it has run on low tank(less than 1/4 of thank full)

Mar 16, 2014 | Chevrolet Impala Cars & Trucks

1 Answer

2000 bonneville starts then dies. Check engine light on


Could be a number of things. If your car starts first thing in the morning and stalls shortly after, only to start again after it sits for an hour, it would be a classic example of a clogged catalytic converter. If it never starts back, I would check the fuel pressure, sounds to me like it could be a clogged fuel filter, faulty fuel pump relay or faulty fuel pump. If you have enough fuel pressure, check for a faulty coil, ignition module, or map sensor vacuum leaks.

Dec 12, 2013 | 2000 Pontiac Bonneville

1 Answer

I have a 93 K3500 with a 454. Truck was running fine, started no problem, ran great. Driving the other day, turn the corner and the engine quit. Cranked the engine, fired up for 2-3 seconds then quit, ...


Before starting the engine, the fuel pump should only run for a few seconds when the key is first turned, to pressurize the fuel system. Even though the pump appears to be running, you may either have not enough or too much pressure for the engine to keep running (fuel pump or pressure regulator). I think it may just be a coincidence the engine quit while turning a corner, but the gas in your tank may have been so low it sloshed away from what is likely a very old pump, starving it and causing it to failure.

Jul 03, 2017 | 1993 Chevrolet C1500

2 Answers

Fuel pump not always on


Did you reset the inertia switch that shuts pump down in case of collision?

Feb 18, 2012 | 2000 Mercury Grand Marquis

1 Answer

The engine on my 2000 MPV cuts out and dies when I press the accelerator. After it sits for an hour or so, I can travel for 20 min. or so before the problem starts again. HELP!


if its been a while change the fuel filter and then have the fuel pressure and volume checked.these symptoms are very common for a fuel pump problem.

Feb 07, 2012 | 2000 Mazda MPV

1 Answer

Just put a used new engine in. new used fuel pump. everything was great until it gave me starting problems. first it didnt want to turn over. started turning the igg. on and off for the fuel pump to...


I think you had the same problem that my aunt had with her Cavalier. The fuel pump
failed. Grandfather installed an aftermarket fuel pump and it worked fine. I hope this
is the solution. (As a side note, I think you were losing prime through the pump).

Jul 31, 2011 | 1996 Chevrolet Cavalier

1 Answer

1990/ cutlas/ siera/ drove/in/ garage/ had/ crack/ silenoid/ replaced/ with/ new/ now/ car/ wont/ start/ turns/ over/ fine/ no/ spark/ to/ any/ silenoids.sillenoid/ 1/ of/ 3


Sounds like a weak fuel pump check your fuel pressure.It should be 40-47 psi with key on engine off and with key on engine running it should be 30-44 psi if its not within specs replace fuel pump.

Apr 30, 2011 | 1990 Oldsmobile Cutlass Ciera

1 Answer

2006 vibe won't start


its not the battery its still cranking isnt it! Probably needs an ecm. By the way it will say Toyota right on it so the toyota version has the same dang problem!!!!

Jul 17, 2009 | 2004 Pontiac Vibe

1 Answer

1998 Pontiac Sunfire won't accelerate


I assume that you do not have a "check engine" light?

The next thing I would do is check the pressure from the fuel pump. You can have this done at your preferred garage, or by purchasing a fuel pressure gauge from any parts store.

Vent the fuel tank vapors by loosening the fuel cap. Remove the electric fuel pump fuse and start the engine. Allow the engine to run until it runs out of fuel and stalls. After spinning the engine over for a period of 3 to 5 seconds, turn off the ignition switch and install the electric fuel pump fuse. Next, install a fuel pressure gauge in the fuel rail supply line, and secure the fuel tank cap. With the ignition key in the on position, verify that no leaks are present and start the engine. Visually verify the PSI reading on the gauge. The pressure for your vehicle should be 41-47 PSI (Pounds per Square Inch). Hope this helps and good luck!

Jan 13, 2009 | 1998 Pontiac Sunfire

1 Answer

WONT START AND PAST IDLE


have a ford garage check out the fuel pump don't do it yourself if you do it will be so messed up they can't even fix it trust me i did i had to scrap the car

Nov 05, 2008 | 1986 Lincoln Town Car

Not finding what you are looking for?
1992 Dodge Power Ram 50 Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...