Question about 1994 Geo Tracker
LSI 4x4 Manual trans
Posted by Anonymous on
for the search engine , i post
this. no cranks
Posted on Dec 14, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
THERE IS A SWITCH UNDERNEATH THE STEERING COLUMN THAT WILL CORRECT THIS PROBLEM. I BOUGHT MY 1994 GEO TRACKER 4X4 BRAND NEW. IT TOOK ME SEVERAL SERVICE APPOINTMENTS FROM MY DEALER BEFORE I GOT THIS INFORMATION FROM MY MECHANIC.
Posted on Feb 01, 2009
1996 Geo Tracker Car Radio Wiring Diagram
Car Radio Battery Constant 12v+ Wire: White
Car Radio Accessory Switched 12v+ Wire: White/Black
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Red/Yellow
Car Stereo Dimmer Wire: Red/Green
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): Black/Blue
Right Front Speaker Positive Wire (+): Blue
Right Front Speaker Negative Wire (-): White/Red
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Light Green
Left Rear Speaker Negative Wire (-): Light Green/Black
Right Rear Speaker Positive Wire (+): Gray
Right Rear Speaker Negative Wire (-): Gray/Black
Posted on Nov 22, 2009
first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.
Posted on May 05, 2010
Guys-no schrader valve-and 92 doesn't have scan capability. Its a fuel problem-so listen at fuel tank inlet with cap off and have someone turn key to on, not start, ON. Hear the pump run for 2 to 3 seconds??, Pump may be ok. next find fuel inlet on back of throttle body and loosen it, don't remove. Key on again does fuel spill out of connection? Pump is OK! Tighten up fuel inlet to throttle body. Make a jumper wire with a 5amp fuse in the middle and alligator clips on each end. Locate the POWER wire to the injector, red I think. Pierce the power wire with a pin or whatever and attach one alligator clip to the pin and the other clip to the positive battery post. Start the car!! IF it starts and runs, the circuit in the PCM that provides power to the injector has burned out. Rebuilt ECMs are on ebay. Common failure. Good Luck!
Posted on May 07, 2010
Tips for a great answer:
Jun 27, 2014 | 1994 Geo Tracker
Sep 02, 2008 | 1992 Geo Tracker
Apr 16, 2014 | Geo Tracker Cars & Trucks
Nov 18, 2013 | 1996 Geo Tracker 2 Door
Feb 14, 2010 | 1993 Geo Tracker
Sep 21, 2009 | 1997 Geo Tracker 2 Door
May 20, 2008 | 1994 Geo Tracker
152 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: