Question about 2000 Pontiac Montana

Open Question

P1626,u1000,is the code i got from a diagnostic tool,what do i do to fix the problem

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTC U1000?


DTC U1000 and U1255
Class 2 Communication Malfunction , Do you know what class 2 serial data communication network is ? What module set this code an what kind of scan tool did you use to read this code .
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the ID number of the module which sent the message for State of Health monitoring, Node Alive messages. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. When a module does not associate an ID number with at least one critical parameter within about 5.5 seconds of beginning serial data communication, DTC U1000 or U1255 is set. When more than one critical parameter does not have an ID number associated with it, the DTC will only be reported once.
The table below list the modules on the Class 2 Serial Data Circuit that will set a U1000 or U1255 and should be actively communicating the previously described messages on the Class 2 Serial Data Circuit.

Control Module

ID Number
Body Control Module (BCM)
064
Electronic Brake Control Module (EBCM)
040
Instrument Panel Cluster (IPC)
096
Radio
128
Powertrain Control Module (PCM)
016
Sensing and Diagnostic Module (SDM)
088
Diagnostic Aids
When a malfunction such as a open fuse to a module occurs while modules are communicating, a Loss of Communication DTC is set as current. When the modules stop communicating, ignition is turned off, the current Loss Communication DTC is cleared but the history DTC remains. When the modules begin to communicate again, the ignition is turned on, the module with the open fuse will not be learned by the other modules so U1000 or U1255 is set current by the other modules. If the malfunction occurs when the modules are not communicating, only U1000 or U1255 is set.
Test Description
The numbers below refer to the step numbers on the diagnostic table.

  1. A DTC U1001 - U1254 Lost Communications with with a history status may indicate the cause of U1000 or U1255.

  2. The modules not communicating are the likely cause of U1000 or U1255. The modules that are available on the class 2 serial data circuit are listed in the Circuit Description.

  3. The module which was not communicating due to a poor connection to the class 2 serial data circuit may have set DTC U1001 - U1254 Lost Communications with for those modules that it was monitoring.

  4. The modules which can communicate indicate the module which cannot communicate. You must clear the serial data communication DTCs from these modules to avoid future misdiagnosis.

  5. If all modules are communicating, the module which set U1000 or U1255 may have done so due to some other condition.

  6. The module which set U1000 or U1255 is the likely cause of the malfunction.

1
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Record the DTCs set in each module. If using a Tech 2, use the Class 2 DTC Check feature to determine which modules have DTCs set.
Did you record any DTCs in the range of U1001-U1254 with a history status?
Go to Diagnostic Trouble Code (DTC) List
Go to Step 2

2
  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to communicate with each module on the class 2 serial data circuit. If using a Tech 2, obtain this information using the class 2 Message Monitor feature.
  3. Record all of the modules communicating on the class 2 serial data circuit.
  4. Compare the list of modules which are communicating to the list given in Circuit Description.
Does any module on the class 2 serial data circuit not communicate?
YES - Go to Step 3
NO - Go to Step 12
Test the following circuits of the module that is not communicating for an open or short to ground:
?€¢
The battery positive voltage supply circuits


?€¢
The switched battery positive supply circuits


?€¢
The battery positive voltage output circuits


?€¢
The ignition voltage input circuits


?€¢
The ignition voltage output circuits

Refer to the following:
?€¢
Control Module References in Body Control System for the applicable schematic


?€¢
Circuit Testing in Wiring Systems


?€¢
Wiring Repairs in Wiring Systems

Did you find and correct the condition?

5

Important: Inspect all connectors in the serial data communications circuit.
Refer to the following:
?€¢
Data Link Connector Schematics


?€¢
Testing for Intermittent Conditions and Poor Connections in Wiring Systems


?€¢
Connector Repairs in Wiring Systems

  1. Turn OFF the ignition.
  2. Test the class 2 serial data circuits of the module that is not communicating for an open. Refer to the following:
?€¢
Data Link Connector Schematics


?€¢
Circuit Testing in Wiring Systems


?€¢
Wiring Repairs in Wiring Systems

Did you find and correct the condition?
Go to Step 8
Go to Step 6

6
Inspect the harness connector of the module that is not communicating for poor connections and terminal tension at the following circuits:
?€¢
The battery positive voltage input circuits


?€¢
The switched battery positive voltage supply


?€¢
The battery positive voltage output circuits


?€¢
The ignition voltage input circuits


?€¢
The ignition voltage output circuits


?€¢
The ground circuits


?€¢
The class 2 serial data circuits

Refer to the following:
?€¢
Control Module References in Body Control System for the applicable schematic


?€¢
Testing for Intermittent Conditions and Poor Connections in Wiring Systems


?€¢
Connector Repairs in Wiring Systems

Did you find and correct the condition?
Go to Step 8
Go to Step 7

7

Important: Perform the module programming or setup procedure if required.
Replace the module that is not communicating. Refer to Control Module References in Body Control System for the appropriate Repair Instructions for the module replacement.
Did you complete the replacement?
Go to Step 10
--

8

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Select the Display DTCs function for the module which was not communicating.
Does the scan tool display any DTCs which do not begin with a "U"?
Go to Control Module References in Body Control System for applicable Diagnostic System Check
Go to Step 9

9
Use the scan tool in order to clear the DTCs.
Did you complete the action?
Go to Step 10
--

10

Select the Display DTCs function for the modules which had U1000 or U1255 set as a current DTC.
Does the scan tool display DTCs which do not begin with a "U"?
Go to Control Module References in Body Control System for applicable Diagnostic System Check
Go to Step 11

11

Use the scan tool in order to clear the DTCs.
Did you complete the action?
System OK
--

12
Did you record any other DTCs for the modules which had U1000 or U1255 set as a current DTC?
Go to
Control Module References in Body Control System for applicable Diagnostic System Check
Go to Step 13

13

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool in order to clear the DTCs.
  4. Turn OFF the ignition for at least 5 seconds.
  5. Turn ON the ignition with the engine OFF.
  6. Select the Display DTCs function.
Does the scan tool display U1000 or U1255 set as a current DTC?
Go to Step 14
Go to Diagnostic Aids

14
Important: Perform the module programming or setup procedure if required.
Replace the module which had U1000 or U1255 set as a current DTC. Refer to
Control Module References in Body Control System for the appropriate Repair Instructions for the module replacement.
Did you complete the replacement?
System OK

Mar 12, 2016 | 2002 Pontiac Grand Am GT1

1 Answer

Code u1000 code p0105 u1152


Codes U1000 & U1152 are related to the digital data bus communications, U1152 is specific for the HVAC control unit data bus. troubleshooting this will require a Tech II scan tool.
P0105 is related to the MAP sensor circuit.

Apr 27, 2014 | 2002 GMC Envoy

1 Answer

CODE U1000 and CODE P1626


you need obd scanner to reset and see if comes back- if it does come back with code , post again

Mar 30, 2014 | 2008 Chevrolet Suburban

1 Answer

U1000 class 2


Does the scanner give you any other read outs ?

Feb 10, 2014 | Buick Cars & Trucks

1 Answer

Diagnostic code u1000


U1000 SCP (J1850) Invalid or Missing Data for Primary Id

Jul 30, 2012 | 2009 Chevrolet Malibu

1 Answer

2000 chevy venture key jammed ignition replaced ignition car wont turn over. OBD-II codes U1000, P0463, P1626. How do I fix problem


Code U1000 is saying the ECM lost communication with the BCM which can happen when the key switch is turned far enough to stop the engine but not enough to turn the accessories off.
Code 463 is for fuel level sensor circuit high which is a problem with the fuel gauge or the sending unit in the tank.

Code 1626 involves the theft deterrent system.
P1626 CHEVROLET - Theft Deterrent Fuel Enable Signal Not Received
Read more: http://engine-codes.com/p1626_chevrolet.html#ixzz210PRFRO9

The code 1626 could be the issue - the passkey system may not be reading the chip in your key.

Jul 18, 2012 | 2000 Chevrolet Venture

1 Answer

How do you reset the security light on a 2005 chevy cobalt?


There is no reset , if security light is lit there is a problem with the anti-theft system .Should have it checked for DTC'S - diagnostic trouble codes . Could have 8 different B - codes
DTC B0685 DTC B2955 DTC B2960 DTC B3031 DTC B3033 DTC P1626 DTC P1630 DTC P1631
You would need a professional type scan tool to read these type codes , not an OBD 2 code reader .

Apr 14, 2012 | Cars & Trucks

1 Answer

U1000 Diagnostics check pop-up


U1000 is a CAN Communication fault code. it is a code that most nissans have that cannot be cleared. does not indicate a fault with any system. if that is the only code in the system then ignore it, does not affect the car

Jul 02, 2009 | 2005 Nissan Maxima

Not finding what you are looking for?
2000 Pontiac Montana Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...