Question about 1993 Ford Ranger SuperCab

Open Question

How to replace the ecm Ford ranger 1993 - 1993 Ford Ranger SuperCab

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1993 ford ranger supercab

the fuse box is inside the pickup under the drivers side dash, there is a flasher which is the round one in the fuse box, it controls turn signals and emergency flashers also in the same fuse box, there is a 15 amp fuse which controls just the turn signals it sits vertical instead of horizontal.

Posted on Oct 23, 2008

Ad
bschilz
  • 2049 Answers

SOURCE: How do I replace the fan belt on a 1993 Ford

You have a serpentine belt. Depending on your engine size, choose the following diagram to help put the belt back on.
V-6 2.3L http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7007
V6- 3.0L http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7012
V-6 4.0L http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7008

Follow this link for a video on how to replace a serpentine belt...
http://www.wonderhowto.com/how-to/video/how-to-inspect-and-replace-your-car-s-serpentine-belt-267229/

Posted on Sep 06, 2009

czaa
  • 4536 Answers

SOURCE: ECM Testing

do a code scan 1st-if no problems then hav computer analysed-they r usually trouble free systems

Posted on Sep 06, 2009

batviper
  • 120 Answers

SOURCE: HOW TO INSTALL CAM SENSER ON 1993 FORD RANGER 4.0

its right behind the intake manifold. its a B*&^h to get off but you need a special tool you can get a most auto part stores. you have to make sure your #1 piston is TDC on your compression stroke. then drop in your sensor, align it to what your specs say

Posted on Nov 18, 2009

  • 1129 Answers

SOURCE: 1993 ranger sputters until warm?

replace the Oxygen senson before catalytic converter this sensor tells the computer to send signal to fuel injectors to allow rich mixture upon start up for warm up then leans out mixture as it heats.

Posted on Feb 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 ford ranger does the ecm control the transfer case


yes it does ... have seen 4X4 in the pinout ...(the plug that goes into the ECM.......

Feb 27, 2014 | 1998 Ford Ranger

1 Answer

1993 Ford Ranger


need the diagram timing ford ranger 1993 motor 3.0L

Dec 07, 2013 | 1993 Ford Ranger SuperCab

1 Answer

I have a 1994 ford ranger that is blowing the fuse under the hood that goes to the ecm


Check for frayed or broken wires comeing from ecm if none replace ecm. make sure ecm ground wire is intact. (ECM is probably the problem.)

Nov 20, 2010 | Ford Ranger Cars & Trucks

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

1 Answer

How does the spring go in on replacing back brakes on 1993 ford r


They make a brake spring installation tool. You can use vise grips, or hook the spring on a screwdriver and get the edge of the screwdriver abve the pin, and pry up, might take a couple tries.

May 02, 2010 | 1993 Ford Ranger SuperCab

1 Answer

1993 ranger sputters until warm?


replace the Oxygen senson before catalytic converter this sensor tells the computer to send signal to fuel injectors to allow rich mixture upon start up for warm up then leans out mixture as it heats.

Feb 24, 2010 | 1993 Ford Ranger SuperCab

1 Answer

1993 FORD RANGER 4 WHEEL DRIVE


there is an actuator on the back of the transfer case that likes to fail odds are this is where your problem is. check power and ground here and if you have both replace the actuator

Nov 22, 2008 | 1993 Ford Ranger SuperCab

1 Answer

1993 ford ranger


check grounds very carefully and clean retighten all you can find ...engine/firewall...battery/chassis etc

Jul 26, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...