Question about 1994 Ford Mustang

1 Answer

When i lsightly step on the gas pedal the rpms get low like its about to stall then it shoots back up

Posted by on

  • yadayada
    yadayada May 11, 2010

    any trouble codes in memeory?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 74 Answers

Vacuum leak

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to TEST A TORQUE CONVERTER ON A Automatic Transmission


Symptom : chattering or vibration while idling, and in Park.
Transmission sluggish upon Accelaration..

Step 1: chock Block all your wheels, and put your Auto emergency brake on (applied).

Step 2: You step on your gas pedal with engine in Drive, Full throttle. do not hold your regular brake pedal...Hold gas pedal down for 2 seconds your car will try to move. All wheels must not slip.

Step 3: watch your rpm gauge, your stall should be between 2400-2800 rpm depending on specification of manufacturer..
a low reading isbad stator assembly,
a high reading is a slipping one way clutch..

on Jul 10, 2010 | GMC Blazer Cars & Trucks

1 Answer

F22a engine produces strange noise most obvious at 2000 rpm, what could the problem be?


Without a general description of what the noice sounds like, squeal as compared to knocking, it is impossible to help you. Engines make a lot of different noises, so try and help by describing noise. I would suspect it is belt related, or tension pulley related as these are RPM variable noises, belts tend to slip when you accelerate and can be quite loud with a serpentine belt as example.
CERACOAT-NANOTECH.com

May 14, 2015 | 1996 Honda Accord

2 Answers

1996 Honda accord Stalling!!


I would replace the fuel filter, double check your work and make sure that all plug wires are securely connected and going to the right place (we all make mistakes sometimes) and check or replace the coil.

Jul 07, 2013 | 1996 Honda Accord

2 Answers

2000 dodge stratus 2.4l dohc stalls at stops starts up with very light touch of gas pedal may or may not stall again for a coule stops but will again rpms go from around 800 at idle to 500 then 200 th


If it's fuel-injected, you may need to have the injectors cleaned, and also, any air filters should be changed at the same time along with gas filter/s. If it's carbureted, the same as above, but have someone clean the carburetor completely. Make sure all air hoses are attached correctly, securely and NOT broken. If broken, replace them.

Sep 19, 2012 | 2000 Dodge Stratus

1 Answer

Have a 1997 Dodge Ram 1500. Truck runs fine until it heats up and the termostat kicks in. It will not idle and the rpms go up and down between 300 and 1000 then stalls. When on the highway it runs fine...


likely your throttle position sensor or idle air control valve. Try disconnecting each one when the problem starts if it corrects you have found the culprit.

Nov 08, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Relaced transmission and now have a rattle sound comind from torque coverter area,noise gets louder when gas pedal is applied and noise goes away during shifting of transmission btu comes right back after...


your torque converter is rattling that is the clutch on the stator inside is worn out... You can stall test your torque converter ...Do this but follow correctly. put on parking brake..on the asphalt,,,, block all four wheels...push the gas to the floor for just 2 seconds...down one, two lift off gas pedal quickly..
when your doing this WATCH your RPMs they should reach to around 2200-2400 between the 2-4 rpm if not the Torque Converter is toast!!!! If your car passes the STAll test then when you tranny was put back on one of the fly wheel covers are rubbing....!!!.

May 17, 2010 | 2003 Lincoln Navigator

Not finding what you are looking for?
1994 Ford Mustang Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...