Question about 2002 Toyota MR2 Spyder

Open Question

2002 mr2 evap canister removal

Need instruction on how to get to the evaporative canister

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 1996 Toyota Previa code p0441

P0441 is Evap Emission Incorrect Purge Flow; the repair you are describing is easy, and should correct the P0441 restricition...I would anticipate no large problems.

Posted on Oct 07, 2008

johnjohn2
  • 5763 Answers

SOURCE: my 2002 toyota sienna has evap system malfunction

You are on the right track, you replaced the vent valve and replaced the vsv valve in the engine compartment that should of solved the problem as long as the correct valves were replaced, i would check for a leak in a hose for the evap system, a smoke test would be a good way, the canister may not be the problem but the valves on the canister, there are a few vsv valves on the canister and also the pressure sensor, the switching valve is very common also, there are so many valves thats why the dealer replacing the canister as an asm, hope this helps also make sure gas cap is good.

Posted on Jan 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Error codes p0442 and po445


Po442 is evap system leak
check intake and all vacuum hoses for leaks
check evap canister and purge valve
Po445 is evap canister purge valve short circuit
check wiring and connection

Apr 16, 2016 | 2002 Jeep Grand Cherokee Limited

3 Answers

2002 Ford f150 evaporative emission control system sensor where is it located


on top of the canister purge can , next to the solenoid of same purpose

Jan 30, 2016 | Ford Cars & Trucks

1 Answer

Hyaunda 2010 check engine light code P0442


code p0442 has 2 possible fault areas

evaporative emission (EVAP) system --small leak detected===causes --hose connection/s--intake leak--EVAP canister--EVAP canister purge valve
and the second possible

evaporative emission system--large leak detected (fuel cap loose/off)===causes--mechanical fault---hose connection/s---EVAP pressure sensor

May 16, 2014 | 2002 Subaru Impreza

1 Answer

Evap code p0441


Error Code: P0441
Fault Area:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
- Evaporative Emission (EVAP) Canister Sealing faulty.
- Pipes between Tank Breathing and Throttle Body leaky/blocked.
- Hose connection(s).
Intake leak.
Solutions:
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
- Perform Output Test.
- Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
- Check Evaporative Emission (EVAP) Canister.
- Perform Basic Setting.
- Check Pipes between Tank Breathing and Throttle Body.

Feb 06, 2014 | 2003 Toyota Land Cruiser

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

1 Answer

How do I fix code P1446 on my 2002 Nissan Pathfinder


DTC P1446 EVAP CANISTER VENT CONTROL VALVE
The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.
This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows "EVAP Control System (Small Leak, Gross Leak, Very Small Leak)" diagnosis.

Contact us on the code link if you need additional details.

Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 25, 2011 | 2002 Nissan Pathfinder

1 Answer

P1446 in a 2002 Nissan Pathfinder


DTC P1446 EVAP CANISTER VENT CONTROL VALVE
The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.
This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows "EVAP Control System (Small Leak, Gross Leak, Very Small Leak)" diagnosis.

Contact us on the code link if you need additional details.

Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 25, 2011 | 2002 Nissan Pathfinder

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Check engine light is on for emission evaporator failure-large


P0455 - EVAP Control System Leak Detected (No Purge Flow or Large Leak) The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).
  • After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
  • Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
  • EVAP canister purge valve stuck closed
  • Damaged EVAP canister
  • Damaged or missing fuel filler cap
  • Insufficient fuel filler cap installation
  • Loose fuel vapor hose/tube connections to EVAP system components
  • Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
  • Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
  • Canister vent (CV) solenoid stuck open
  • Mechanically inoperative fuel tank pressure (FTP) sensor
Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank. ----------------------------------------------------------------------------- HX43 DTC P0457: CHECK FOR MISSING OR LEAKING FUEL FILLER CAP
  • Check for missing fuel filler cap.
  • Check for loose fuel filler cap.
  • Check for possible cross-thread fuel filler cap condition.
Is a fault present concerning the proper installation of the fuel filler cap? Yes No REPLACE cross-threaded or damaged fuel filler cap. RECONNECT and TIGHTEN the fuel filler cap only one eighth turn so that the cap initially clicks by sound or touch. CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test . If DTC P0455 or P0457 is present, Go to HX44 . CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test .

For DTC P0455 still present: Go to HX44 .

Otherwise, INFORM the vehicle owner that it is important and necessary to immediately install the fuel filler cap after every refueling event. HX44 DTC P0455: VISUAL INSPECTION FOR SUBSTANTIAL EVAPORATIVE EMISSION SYSTEM LEAKS
  • Check for missing fuel filler cap. If the cap is loose DO NOT DISTURB EVAP system.
  • Verify that both the input port vacuum hose and EVAP return tube are attached to the EVAP canister purge valve. Note: If the EVAP canister-CV solenoid assembly is not accessible during this pinpoint test step, GO to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for disconnected or cracked fuel vapor hoses/tubes between the intake manifold, the EVAP canister purge valve, the EVAP canister, the fuel vapor vent valve assembly and if applicable the fuel vapor control valve tube assembly.
  • Check for damage to the fuel filler pipe and the fuel tank.
Is a fault indicated? Yes No CONNECT or REPLACE fuel vapor hoses/tubes as required. REPLACE damaged EVAP system components (fuel filler pipe, fuel vapor vent valve assembly, fuel vapor control valve tube assembly, EVAP canister purge valve, FTP sensor and EVAP canister-CV solenoid assembly) as necessary. REFER to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions. GO to HX45 . GO to HX45 . HX45 DTC P1443 and P0455: CHECK FOR EVAPORATIVE EMISSION SYSTEM LEAKS
    Note: When checking for leaks or blockages in the EVAP system, energize (close) the canister vent (CV) solenoid through the scan tool for a maximum of nine minutes per pinpoint test step. Then de-energize the CV solenoid prior to performing the subsequent pinpoint test step. This is done to assure proper closing of the solenoid.
  • Disconnect and plug the EVAP return tube (EVAP canister purge valve to intake manifold) at the intake manifold vacuum source.
  • Connect scan tool.
  • Key on, engine off.
  • Access VPWR PID. If the voltage is not 12 volts or greater, GO to HX61 .
  • Locate evaporative test port [marked EVAPORATIVE SERVICE PORT DO NOT USE UNREGULATED PRESSURE ABOVE 6.89 kPa (1 PSI)] near EVAP canister purge valve or EVAP canister.
  • If vehicle is not equipped with the evaporative test port, GO to HX50 .
  • Install the Rotunda Evaporative Emission System Leak Tester 310-F007 (134-00056) or equivalent at the evaporative test port.
  • Close CV solenoid by accessing Output Test Mode on the scan tool.
  • Select ALL OFF mode and push START button.
  • Regulate the nitrogen or argon gas pressure on the tester to 3.48 kPa (14 in-H 2 O).
  • Follow the instructions that come with the EVAP System Leak Tester and pressurize the EVAP system.
  • Perform the EVAP system leak test.
Does the pressure on the EVAP system stay above 1.99 kPa (8 in-H 2 O) and pass the leak test? Yes No GO to HX46 . REMOVE the EVAP System Leak Tester from the evaporative test port and REINSTALL the test port cap. GO to HX50 .

Apr 15, 2009 | 1999 Lincoln Town Car

1 Answer

Location of Charcol Canister and EVAP Emission control solenood valve in hyundai elentra 2002.


The evaporative emission canister purge solenoid valve is a duty control type, which controls the flow of purge air from the evaporative emission canister.
4a6acf4.gif Inspection 1. Look for loose connections, sharp bends or damage to the fuel vapor lines. 2. Look for distortion, cracks or fuel leakage. 3. After removing the EVAP canister, inspect for cracks or damage. 0e0e1be.gif

Sep 03, 2008 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
2002 Toyota MR2 Spyder Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...