Question about 2007 Mini Cooper Convertible

Open Question

Where is the flasher relay on mini r52 - 2007 Mini Cooper Convertible

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does one find the signal ligt flasher unit on a MINI Cooper S R56 Hatchback?


Newer vehicles have the flasher built into the hazard switch.

Feb 05, 2015 | Mini Cars & Trucks

2 Answers

I have a 1998 ford windstar mini van


do your signals work ? listen when signal is on the (clicking noise) when you find that flasher relay is next to it.

Aug 29, 2014 | 1998 Ford Windstar

1 Answer

Reseting auto gear box transmission on 2006 Mini Cooper


I believe the icarsoft i910 tool you can reset all the MINI DTC fault codes including tranny issues. This one

Dec 07, 2013 | Cars & Trucks

1 Answer

Turn signals stopped working but were working yesterday. Any ideas?


More than likely the electronic turn signal flasher is defective.
Instructions
  1. Remove the Old Flasher Relay
    • Using your socket wrench, disconnect the negative cable from the car's battery terminal. The negative terminal and cable are identified on the top of the battery using the minus ("--") symbol. Once the cable is disconnected, wrap the metal end completely with the black electrical tape. Lay the cable down and make sure it's not touching any metal surfaces.
    • 2Open the driver side front door and kneel or position yourself so that you're able to see under the dashboard.

    • 3Locate the automotive flasher relay under the dashboard on the right-hand side. The flasher relay is about the same size as an ice cube. It will be held in place by one screw and will have a three-pronged wiring harness connected to it.
    • 4Remove the screw holding the flasher relay in place and slowly lower it from underneath the dashboard.
    • 5Hold the flasher relay in one hand, and with the other hand gently disconnect the wiring harness plug from the relay. Never separate the flasher relay by pulling the harness off by the wires, always hold the plastic harness plug itself.
    Install the New Flasher Relay
    • 6Inspect the new flasher relay to make sure it isn't damaged. Hold the new flasher relay and the old one side by side and compare them, ensuring that they are exactly the same.
    • 7Carefully plug the wiring harness connector into the new flasher relay. Make sure no other wires are intertwined as you raise the flasher and harness back into position under the dashboard.
    • 8Secure the flasher relay by returning its mounting screw.
    • 9Unwrap the negative battery cable's connector and reattach it to the car's battery terminal. Turn the power on or start your car and test out the new flasher relay to make sure it's working properly

Nov 08, 2012 | 1998 Ford Taurus

1 Answer

Find out where the flaher is located. Also how do you get the heater motor relay out?


the flasher is located in the fuse panel along with the heater relay

Dec 09, 2009 | 1996 Chevrolet Lumina Mini

3 Answers

91 Chevy K5 Blazer turn signal flasher


located under the instrument panel to the left of the steering column. The fuse block should be visible from underneath the steering column, near the pedal bracket.

47a6e67.gif
Some models may use an underhood fuse/relay panel


If the panel is not visible, check for a removable compartment door or trim panel which may used on later models to hide the block. This panel is usually located on the left end of the instrument panel.
The convenience center is located just below the instrument panel on the drivers side. It contains individual relays such as the seat belt and ignition key alarm, and flasher.
On newer model vehicles there is an underhood fuse/relay center contains both mini and maxi fuses, as well as some relays.

Replacement The turn signal and hazard flasher units are usually located in the convenience center located just below the instrument panel on the drivers side. Replace the flasher by unplugging the old one and plugging in the new one. Confirm proper flasher operation.

Nov 03, 2009 | 1991 Chevrolet S-10 Blazer

1 Answer

Abs fuse


Fuses are listed here

* = maxi fuse

1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay

6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay

mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump2.gif relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator


Interior fuse panel (mini fuses)

1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**

15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat, Message center Attached images fuse%20box001.jpg?imgmax=800 __________________

Oct 29, 2009 | 2003 Ford Explorer

2 Answers

No flashers or turn signals


Try the fuse/breaker panel under hood, drivers side.

Jun 20, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
2007 Mini Cooper Convertible Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mini Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mini Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...