Question about Smart fortwo

1 Answer

Blinking wrench -6 - fortwo Smart Cars & Trucks

Posted by Anonymous on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Smart Expert
  • 489 Answers

Major service required

Posted on Aug 07, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Need hex wrench for intex control unit

if bought new the multi tool is included if used any hardware/or store selling tools carries the hex key

Jun 11, 2017 | Cars & Trucks

1 Answer

How to install the trunk lid torsion bars on a 2007 Saturn Ion?

The procedure is the same on every vehicle that uses this type of opening assist. So here is another persons instructions on a GM product.
Tools used:
Leather gloves!!
3/4" combo wrench (biggest I had)
1/2" deep socket (3/8")
6" extension (3/8")

1.With the trunk lid up and the curved part of the torsion bar against the rear trunk wall, I slipped the box end of the combo wrench around the torsion bar. I don't remember which way I had the angle of the box end facing. Just use what will work.

2.Then use the extension and the socket on the end of the torsion bar and push back so that you can get the combo wrench down past the curve, this is key. Once that is done you can remove the socket and extension. Pressure will push the wrench against the rear trunk wall.

3.Now comes the fun part. Push the wrench forward (VERY CAREFULLY) all the way past the side engine grill support and onto the peg of the hinge. The tip of my torsion bar just nicked the grill support. Make sure the wrench is seated well because it could slip around on you and cause your paint some damage and maybe even you.

4.Now that the torsion bar is on the hinge peg, you'll notice that your left with a wrench stuck on the bar... Just move (wiggle, twist) the wrench as far to the end of the torsion bar as it will go.

5.Take the extension, without the socket and place over the tip of the torsion bar. Push down while you slip the wrench past the peg. Remove the extension and slip off the wrench.

6.Now use the extension again to push down and put the roller (plastic, metal) bearing onto the peg.

7.Secure all the bolts, and lube it up.

That's it. Hope it'll help someone else. Please be careful.

Feb 09, 2017 | Saturn Cars & Trucks

1 Answer

Wrench light

Blinking is not good

Stop using it before you hurt the engine

Have a repair shop check for codes,diagnose & resolve

When a check light blinks,sometimes it is an indication of
a cylinder misfire so severe, it could damge the exhaust
converter, & may even go into fail safe, to protect it & you
won't be able to drive it

Just one possible reason for the light blinking

Each manufacturer has different strategies

Aug 01, 2012 | 2001 Chevrolet Impala

1 Answer


no, it has an internal filter that is under a plastic cover, just need a allen wrench and a oil filter wrench

Nov 26, 2010 | 2004 Mazda 6

1 Answer

97 accord, trying to replace the rotors... got the 4 bolts off and the axle nut but cant free the plate in front of the rotor. Might be a rust issue.

The two mounting bolts are installed with Lock tight sealer. Use a 6 pointed boxed end wrench and a hammer on the two bolts. Hit the wrench hard to loosen these bolts up. An impact wrench is much easier to use

Nov 14, 2010 | 1997 Honda Accord

1 Answer

What tools do I need to replace the brakes

To Replace Brake Pads...
1. Brake Pad Set

1. C-Clamp
2. Flat Head Screwdriver
3. Jack Stand Set
4. 3/8 in. Drive Ratchet
5. Combination Wrench Set
6. Tire Iron
7. Socket Set
8. 1/4 in. Drive Torque Wrench
9. Dial Indicator

To Replace Brake Shoes...
1. Brake Shoe Set

1. Combination Wrench Set
2. Floor Jack
3. Jack Stand Set
4. Mallet Hammer
5. Brake Spring Tool
6. Flat Head Screwdriver
7. Needle Nose Pliers
8. Tire Iron
9. Brake Resetting Gauge

1. Brake Cleaner

Hope this helped (remember comment and rated this).

May 05, 2010 | 2000 Dodge Stratus

1 Answer

What size is the rear brake bleeder valve ( i think i am using the wrong wrench)

most of them are 5/16.. if it goes on tight and slips under torque, corners are rounded use a 6 point wrench or socket.. most cheap ( and not so cheap) 12 point wrenches will strip the edges, they wont grab far enough down.

Apr 13, 2010 | 1999 Jeep Cherokee

2 Answers

How do I release belt tensioner on a 1999 taurus 6 cyl

Use a breaker bar and socket or really long wrench and the pulley will either move up or down.

Sep 03, 2009 | 1999 Ford Taurus

2 Answers

2005 grand caravan ? size allen wrench to remove rear calipers

6 mm to small 8 mm to big, how about 7 mm would you not think ??

Aug 16, 2009 | 2002 Dodge Grand Caravan

1 Answer

Belt for 98 ford windstar

Purchase a serpentine belt wrench. They are a long flat looking wrench from a local auto store. There is a belt tensioner in the rear of the engine. Place the wrench on the tensioner pulley, and pull the wrench toward the front of the engine. This will loosen the belt. Install the belt around the crankshaft, and all other pulleys, excluding the alternator pulley. Hold the last bit of the belt in your hand, and then pull the tensioner toward the front of the engine again, and slip the belt onto the alternator pulley.
V-6 3.8 l

V-6 3.0L

Mar 19, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smart Experts


Level 2 Expert

489 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

902 Answers

Are you a Smart Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides