Question about 1988 Cadillac Seville

1 Answer

Carburator mixture screw on 88 cadillac - 1988 Cadillac Seville

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

Looking for the jet screw/screws or trying to adjust?

Posted on Apr 16, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Idle adjustment at carburator end


most older cars had 2 adjustments , a air screw for enrichment and throttle screw for engine idle speed, later models did away with the enrichment screw, to adjust set idle screw to 600 rpm, adjust air mixture screw to fastest rpm , reset idle screw to preferred idle speed.

Oct 03, 2016 | Cars & Trucks

3 Answers

Carburator and idle problem


Believe it or not you just said the solution to your own problem manufacturers specs requires for any adjustments to engine idle or other carburator adjustments to be preformed while the engine is idling and at normal operating temp in plain english let the car warm up then make your idle and mixture adjustments if this doesnt solve it i would check the auto choke and make sure it is opening at normal operating temp hope this helps good luck

Sep 01, 2008 | 1984 Toyota Tercel

1 Answer

How to adjust the carburator


What vehicle? Most have an idle mixture screw, and an idle speed screw. Some have adjustable float settings (Holley). Explain symptoms.

Jun 12, 2015 | Cars & Trucks

1 Answer

Which way does the mixture screws have to go to clean out the carburetor on a 1980 Ford Econoline 250 4.9 liter


I hate to disapoint you but the mixture screw will not clean out your carburator. It is vary easy to rebuild this carb I have an 85 2.8 2 barral have rebuilt it 4 or 5 times for about 30 dollars for kit its a Rodchester .So get the kit get some brake cleaner with the tube to spray through the passages its basiclly a power valve and new gaskets take it apart and clean it and it will work like new evertime

Mar 18, 2015 | Ford Cars & Trucks

1 Answer

Opel kaddet 1995 model. How do I adjust the


There are only two adjustments on a carburetor, the air mixture setting and the butterfly valve position setting. The air mixture screw is on the side close to the mounting flange, and has a spring behind the screw head to keep it in position.
To adjust it, look for the throttle valve screw which is also on the side, it ix the one that attaches close to where the throttle cable attaches to the carb. Turn the set screw down to let the car idle as slowly as possible. Now go to the air mixture screw. Turn it slowly first in one direction until the revs drop, then turn it out to the point where the revs are maximum. You might have to turn the screw back and forth until you find the best position. Now turn the throttle adjustment back to idle speed.

Aug 28, 2014 | Opel Kadett Cars & Trucks

1 Answer

How can you adjust the carburetor on a 1987 GMC safari van V-6


If the carburator has never been rebuilt, or the plugs that were installed at the factory have never been removed, you need to remove those plugs, there is one for each idle mixture screw, at the front of the base plate on the bottom of the carburator, 1 for the TPS adjustment on the driver side front of the carburator, and one for the mixture control solenoid on top of the carburator, in the middle, towards the front.

May 22, 2010 | 1987 GMC Safari

1 Answer

I have an 88 camaro but a carburated engine (350). how can i get this through ct emissions?


first get a pretest test done, then you will know what areas require attention, hc a co2, are indications of unburned fuel in the system, nox emissions are usually controlled by the egr valve, good plugs, filters, pcv valve, vacuum system , choke, fuel mixture, calatytic convertors, timing, engine temperature, exhaust integrety are all factors in emissions

May 10, 2010 | 1998 Chevrolet Camaro

1 Answer

How to adjust fuel mixture 2 barrel carburater for


In the late 70's they mandated that the adjustment screws be capped over. If they haven't been exposed, there will be two plugs covering them on the baseplate. Air adjustment screws are always somewhere on the base of all carbs with the only exception being on Holley 4bbl carbs used on performance engines (definitely not yours)

Nov 18, 2009 | 1983 Toyota Corolla Tercel

2 Answers

How to adjust air fuel mixture on a 87 suzuki samuria


On any carburator,one screw is for the idle speed, the other the air/fuel mix.Start the engine and let it get plenty warmed up. Adjust the idle screw to make the engine run slow. Turn the air/fuel screw in until the engine starts to die then out till it starts running loady.You want the screw between these two locations. Adjust it till the engine runs the fastest. Now adjust the idle speed screw to about 1000 RPM.
I hope this helps you.

Sep 24, 2009 | 1993 Suzuki Samurai

1 Answer

Pick up truck runs in park & neutral but,will not stay runnimg im drv.


Timing may be retarded.Check for vacuum leaks.If carburated, adjust idle mixture screws w/truck in drive(and someones foot on the brake) and/or fast idle screw.

Sep 16, 2009 | 1985 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...