Question about 2001 Cadillac Catera

1 Answer

The oil cap

Cannot remove it is verry hard it's there a way i could fix this problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cadillac Master
  • 354 Answers

Go to the gym!

Posted on Apr 17, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There's hardly any vacuum when you remove oil filler cap when engine is idling


There is not suppose to be vacuum from the crankcase so having none with the oil cap removed is normal.

Nov 11, 2015 | Cars & Trucks

1 Answer

2006 HONDA PILOT OIL PAN REMOVAL


IS HARD TO DO THE JOB ON THE DRIVEWAY BUT I WILL GIVE YOU SOME DIRECTIONS.
DISCONNECT THE BATTERY
RISE THE VEHICLE AND DRAIN THE OIL
REMOVE THE EXHAUST PIPE FROM CAT.CONVERTER.
REMOVE THE SMALL CAP FROM TRANSMISSION LOWER SIDE COVERING THE FLEX PLATE.
REMOVE THE BOLTS FROM THE OIL PAN .
CLEAN THE GASKET FROM PAN AND ENGINE.
INSPECT THE OIL STRAINER AND CLEAN.
REPLACE THE GASKET AND INSTALL 4 BOLT TO FIX TO THE PAN IN POSITION.
INSTALL THE PAN AND DRIVE HALF WAY THE 4 BOLT.
INSTALL THE REST OF YOUR BOLTS AND TIGHT SLOWLY .
REPEAT IN 3 STEPS TIL TIGHT.
IF YOU SEE THE GASKET START TO BLOW OUT OF THE PAN, STOP. IF YOU OVER TIGHT WILL BRAKE THE GASKET AND WILL LEAK.
GOOD LUCK

Apr 23, 2014 | 2006 Honda Pilot

3 Answers

How do you replace the head gasket


with great difficultry, It is verry time consuming end verry costly to have it (Replaced)

Nov 27, 2012 | 2000 Kia Sportage

1 Answer

ENGINE OIL IN DISTRIBUTER CAP


friend get your engine gas-kit check it may be the reason where engine oil and water mixing

May 02, 2012 | Cars & Trucks

2 Answers

Passenger side at end of axle losse inside rotor is loose on bearing and flopping inside with wheel off will just a bearing fix this


most likely it will be just the bearing, unless someone has driven it this way for prolonged time in this case it might need other parts as well such as a new axel, or even a rotor. if it has been the case then the axel nut that holds the axel in the bearing has gotten so hot the chances of loosining it up will be verry slim and verry hard to remove, thus damaging the axel nut threads. if nit is this loose, I would expect to replace the bearing and the axel.

Dec 31, 2010 | 2001 Hyundai Accent

4 Answers

Is the replacement of the brake light bulb under warranty for a 07 versa hatchbacK?


this may or may not be you can call your local dealership and ask. if not then it's only a couple dollars at the part store and a verry easy fix. just pull the carpet down in the trunk behind the tail light and remove the small 10mm nuts the light will now pull out and you can replace the bulb. verry simple

Mar 14, 2010 | 2007 Nissan Versa 1.8 Sl Hatchback

2 Answers

Oil leaking on top of engine..is it valve seals?


it's verry likely your valve cover gasket is leaking. that is one of the first seals to go but it is an easy fix at least. use some gasket sealer or a neopreene gasket the corque gaskets are obsolete and they don't last very long.

Apr 15, 2009 | 1990 Jeep Cherokee Limited

1 Answer

Replacing oil pump


hi had same problem was oil intake screen clogged with sludge, remove oil pan and clean intake screen. verry easy job to perform

Feb 10, 2009 | 1998 Isuzu Amigo

1 Answer

I'm almost embarassed to ask this question. I have a 1999 Chrysler 300M and it needs a quart of oil. I can't get the oil cap off - it just spins around freely. No matter how hard I press down on the cap...


well if you have no success taking the cap off and you really need the oil there is another way to put the oil in your car at least until you get th cap fix. thake the dipstick out of the tube and put a funnel in it and ad the oil tha way. at least you have the oil in the car and your not chancing running the engine.

Aug 01, 2008 | Chrysler 300M Cars & Trucks

Not finding what you are looking for?
2001 Cadillac Catera Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...