Question about 1998 Volkswagen Beetle

1 Answer

How to remove a 095 927 331 a solenoid - 1998 Volkswagen Beetle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Volkswagen Master
  • 733 Answers

Send me a email at tcifusion a yahoo.com to provide u wit further info.

Posted on Apr 16, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the purge valve on 2006 Yukon Denali


Replacing Vent Valve Solenoid Purge Valve Solenoid EVAP Valve 2005 GMC...

Remove the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement . Remove the evaporative emission (EVAP) line from the canister purge solenoid, perform the following:
2.1.
Push the large size white retainer portion in.


2.2.
Push down, while pulling up slightly in order the disengage the tube.


Disconnect the EVAP canister purge solenoid electrical connector (1).
Remove the EVAP canister purge solenoid bolt (2). Remove the EVAP canister purge solenoid (3) and insulator (1).

Sep 19, 2015 | Cars & Trucks

1 Answer

I have a 1999 oldsmobile aurora, northstar motor. I was told I need to replace my purge valve solenoid. Can someone please tell me where it is located?


It's under the plastic cover on top of the engine . Remove the intake manifold top cover.
Remove the solenoid quick-connect hose (3) at the EVAP canister purge solenoid (4). Remove the solenoid quick-connect hose (7) from the EVAP canister purge solenoid (4) to the enhanced EVAP service port (8). Remove the electrical connector (6) at the EVAP canister purge solenoid. Remove the EVAP canister purge (2) solenoid valve bolt. Remove the EVAP canister purge solenoid tab from the bracket (5).

Aug 06, 2015 | 1999 Oldsmobile Aurora

1 Answer

Where is a shift solenoid located on a ford f150


They are in the transmission . Remove the transmission fluid pan. You will see the valve body , the solenoids are mounted to it. They are clipped in. Do not remove the valve body unless you have to. Things pop out of it. Be careful removing solenoids, things can pop out of these holes also. Hold the solenoid and remove the clip/s.

Feb 10, 2015 | 2004 Ford F150

1 Answer

Purge solenoid location 2008 torent


Evaporative Emission Canister Purge Solenoid Valve Replacement
Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Disconnect the engine wiring harness electrical connector (4) from the evaporative emission (EVAP) purge solenoid.
Remove the oil fill cap. Lift upward and remove cover from ball studs.
The purge solenoid is under the plastic cover on top of the engine .
Disconnect the EVAP pipe quick connect fitting (1) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the EVAP pipe quick connect fitting (2) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service. Remove the EVAP purge solenoid bracket bolt (3). Remove the EVAP purge solenoid.

the purge

Sep 20, 2014 | 2008 Pontiac Torrent

1 Answer

I need to replace shifting solenoid on 1990 Chevrolet 1500


you need to remove transmission oil pan,be careful oil will come out no plug to remove.remove clip or bolt from 1/2shift solenoid and clip or bolt from 2/3 shift solenoid remove solenoid ( reverse proc.)

Aug 14, 2013 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Where is the starter solenoid located on a 1991 mazda mpv


  1. Remove the starter from the truck.
  2. Disconnect the field strap from the solenoid terminal.
  3. Remove the two solenoid attaching screws.
  4. Disengage the solenoid plunger from the shift fork and remove the solenoid.
  5. Install the solenoid on the drive end housing, making sure that the solenoid plunger hook is engaged with the shift fork.
  6. Apply 12v to the solenoid S terminal and measure the clearance between the starter drive and the stop-ring retainer. It should be 2.0-5.0mm (0.0787-0.1969 in.). If not, remove the solenoid and adjust the clearance by inserting an adjusting shim between the solenoid body and drive end housing.
  7. Check the solenoid for proper operation and install the starter.
  8. Check the operation of the starter.


4fcbf48.gif
It is number 1, bottom right hand corner of this picture....

Here is the link:

http://www.chiltonlibrary.com/content/images/8964/images/89642g19.pdf

If it does not open, please let me know.

Oct 30, 2010 | 1991 Mazda MPV

1 Answer

Starter solinoid replacement enstruction


SOLENOID REPLACEMENT
(see Figures 5, 6 and 7)

Prior to removing the solenoid from the starter motor unit, matchmark the solenoid-to-starter motor housing position, as shown in the accompanying illustration.
  1. Remove the starter motor from the vehicle.
  2. Detach the solenoid-to-starter motor wire from the solenoid terminal.

Do not disassemble the solenoid; if the solenoid is defective, replace the entire unit with a new one.
  1. Remove the two attaching screws, then slide the solenoid out of the starter motor housing flange.
9b9a219.jpg

Fig. 5: Before removing the starter motor solenoid, matchmark the solenoid-to-starter motor housing relationship

44d3238.jpg

Fig. 6: Disconnect the field coil lead from the solenoid by loosening the retaining nut ...

e357fdb.jpg

Fig. 7: ... then remove the two attaching screws and separate the solenoid from the motor housing


To install:
  1. Inspect the solenoid plunger joint for wear or other damage. Replace it, if damage is evident.
  2. Apply Suzuki Super Grease A (99000-25010) or equivalent, to the solenoid plunger and to the tip of the lever arm (inside the starter motor-to-solenoid housing hole).
  3. Insert the solenoid into the starter motor housing, ensuring that the matchmarks made during removal are aligned.
  4. Install and tighten the two attaching screws securely.
  5. Attach the starter motor-to-solenoid wire to the solenoid terminal.
  6. While the starter motor is removed form the vehicle, perform the testing procedure to ensure that the new solenoid functions properly.
  7. Install the starter motor.

Hope this help (remember rated and comment this).

Mar 23, 2010 | 1994 Geo Tracker

1 Answer

I can't locate the starter solenoid on my 2000 chevy silverado. Where is it?


(Starter) Solenoid - Removal & Installation
  1. Remove the starter motor.
  2. Reposition the M-terminal stud weather cover.
  3. Clean the epoxy coating from the M-terminal stud.
  4. Loosen the M-terminal stud nut.
  5. Remove the cable from the M-terminal stud.
  6. Remove the solenoid bolts.
  7. Separate the solenoid from the housing and unhook the solenoid plunger from the drive gear lever.
  8. Note that the spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2).

    335574b.jpg

    Fig. Spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2)
  9. Remove the solenoid housing.
  10. If necessary, remove the solenoid plunger and spring.
To install:
  1. If necessary, install the solenoid plunger and spring.
  2. Using Three Bond silicone 1207B, GM P/N 97720043, seal the starter solenoid attachment area.
    WARNING Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop. Improper installation of the drive gear lever will cause an abnormal or no operation condition of the starter.
    9d089a5.jpg

    Fig. Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop
  3. Install the solenoid, making sure to insert the drive gear lever (1) into the solenoid plunger (2) loop, perform the following:
    1. Pull the gear lever (1) out away from the starter housing and pull the plunger (2) out away from the solenoid.
    2. Tip the solenoid and insert the lever into the loop, push the solenoid against the housing.
  4. Install the solenoid bolts and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Wipe the excess silicone pressed out during the solenoid installation from around the base of the solenoid to make a weather proof seal.
  6. Install the cable to the M-terminal stud between the washers and terminal nut.
  7. Tighten the M-terminal stud nut and tighten the nut to 71 inch lbs. (8 Nm).
  8. Using Three Bond silicone 1207B, GM P/N 97720043, seal the M-terminal stud connection.
  9. Reposition the M-terminal stud weather cover.
  10. Bench test the starter in a free-run condition prior to installation.
  11. Install the starter motor.

  1. Remove the starter motor.
  2. Reposition the M-terminal stud weather cover.
  3. Clean the epoxy coating from the M-terminal stud.
  4. Loosen the M-terminal stud nut.
  5. Remove the cable from the M-terminal stud.
  6. Remove the solenoid bolts.
  7. Separate the solenoid from the housing and unhook the solenoid plunger from the drive gear lever.
  8. Note that the spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2).

    fe8b46d.jpg
    Fig. Spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2)
  9. Remove the solenoid housing.
  10. If necessary, remove the solenoid plunger and spring.
To install:
  1. If necessary, install the solenoid plunger and spring.
  2. Using Three Bond silicone 1207B, GM P/N 97720043, seal the starter solenoid attachment area.
    WARNING Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop. Improper installation of the drive gear lever will cause an abnormal or no operation condition of the starter.
    257f66c.jpg

    Fig. Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop
  3. Install the solenoid, making sure to insert the drive gear lever (1) into the solenoid plunger (2) loop, perform the following:
    1. Pull the gear lever (1) out away from the starter housing and pull the plunger (2) out away from the solenoid.
    2. Tip the solenoid and insert the lever into the loop, push the solenoid against the housing.
  4. Install the solenoid bolts and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Wipe the excess silicone pressed out during the solenoid installation from around the base of the solenoid to make a weather proof seal.
  6. Install the cable to the M-terminal stud between the washers and terminal nut.
  7. Tighten the M-terminal stud nut and tighten the nut to 71 inch lbs. (8 Nm).
  8. Using Three Bond silicone 1207B, GM P/N 97720043, seal the M-terminal stud connection.
  9. Reposition the M-terminal stud weather cover.
  10. Bench test the starter in a free-run condition prior to installation.
  11. Install the starter motor.

Hope helped with this (remember rated this help) Good luck.

Nov 04, 2009 | 2000 Chevrolet Silverado

3 Answers

How do you put a starter solenoid in a 1988 ford f150?


Ford does not put the solenoid on the starter itself, so then it is just a relay, usually on a fender. It will have 4 wires. Two thick ones from the battery and to the starter. And 2 thin ones from ignition switch and to ground.

Oct 31, 2009 | 1988 Ford F 150

1 Answer

PROBLEMS WHITH THE TRANSMISSION CONTROL SOLENIOD


===shift interlock solenoid--Inside the steering column near the ignition switch

===1-2 shift solenoid valve--Inside the automatic transaxle
to remove it :
  1. Remove the case side cover. Refer to Case Side Cover Replacement.
  2. Disconnect the transaxle wiring harness.
  3. Remove the 1-2 shift solenoid (315A).
2-3 shift solenoid valve--Inside the automatic transaxle
to remove it;
  1. Remove the case side cover. Refer to Case Side Cover Replacement.
  2. Disconnect the transaxle wiring harness.
  3. Remove the 2-3 shift solenoid (315B).
==the torque converter solenoid--inside tranny too

good luck,let me know

Jun 04, 2009 | 2000 Pontiac Montana

Not finding what you are looking for?
1998 Volkswagen Beetle Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...